I had a problem similar to yours in a church auditorium. It turned out to be poorly soldered wires inside a phone pug with an all metal body. A strand of "hot" wire had come loose and touched the metal body of the phone plug used to connect the amp to the speakers. Double check the wire used to connect the amp to the speakers. Any wire strands loose at either end? Since the amp has played in a shop and folks have had it out of the case, it shouldn't be dirt and fuzz on the heat sinks. If you have a fan available, point it at the air inlet of the cabinet and turn it on high before you turn on the amp. Does it take longer to shut off with the air blowing on it? If so, take the cabinet off and see if that helps. Also, be sure the small screws holding the output transistors in place are tight. Look for stray bits of conductive material in the cabinet or chassis f the amp. The two techs should have cleaned it out very well. Any stray wires around the amp's output connectors? Use a strong flashlight and wiggle it around. Tiny strands of wire can be very hard to see. Good luck.
What could cause this amp to fail?
Hi Everyone,
Apologies if this is the wrong forum for this question. I just got into serious speakers (been into headphones most of my life). I picked up a pair of Thiel CS1.5’s that have blown me away. Anyways, I also bought a used Perreaux EX-120 (circa 1994 MOSFET Class AB 100wpc) Integrated amp on ebay for pretty cheap (seller had no feedback and I decided to take a chance) which is the subject of this question.
For the first few days after plugging it in it sounded great: warm, smooth, powerful until on around the fifth day, I noticed the sound cut from the amp and what sounded like a click. I powered it down and let it rest. The next day I heard the same thing but it started to happen more and more frequently. It would start about a minute after starting to play music and then quickly increase to the point where it would be clicking and cutting out multiple times per second (it doesn’t happen if no signal is running through). There was also a noticeable clicking coming from within the amp itself. The problem now starts happening immediately after putting signal through it and doesn’t stop.
I took it to a local audio repair who thought it was a relay issue but was unable to fix it after several tries. He referred me to another repair shop who has now told me that 8 Mosfets in the amp are blown and the input selector has ’aged out’. To repair it would cost about $450 dollars as he would have to replace many components in the amp and that it would end up as a just a power amp since the selector is a custom component that Perreaux doesn’t sell anymore.
I’m trying to get my money back from the seller, but he’s pretty much refusing saying that this is impossible and suggesting that I must have overloaded it since it worked when he sent it out. One thing to note is that I have carpet (not deep, quite short) and the binding posts on the Thiels are at the very bottom where I imagine it’s possible that the carpet could come into contact with the connectors. I have 2 other amplifiers (an entry level Cambridge Integrated and a B&K receiver which is a MOSFET design) and neither have had this issue.
My question is: could static electricity or contact between the carpet and the binding posts/cable connectors cause the amp to fail? If so, how come it took 4-5 days? If not, what is the possibility that it is my fault?
Apologies if this is the wrong forum for this question. I just got into serious speakers (been into headphones most of my life). I picked up a pair of Thiel CS1.5’s that have blown me away. Anyways, I also bought a used Perreaux EX-120 (circa 1994 MOSFET Class AB 100wpc) Integrated amp on ebay for pretty cheap (seller had no feedback and I decided to take a chance) which is the subject of this question.
For the first few days after plugging it in it sounded great: warm, smooth, powerful until on around the fifth day, I noticed the sound cut from the amp and what sounded like a click. I powered it down and let it rest. The next day I heard the same thing but it started to happen more and more frequently. It would start about a minute after starting to play music and then quickly increase to the point where it would be clicking and cutting out multiple times per second (it doesn’t happen if no signal is running through). There was also a noticeable clicking coming from within the amp itself. The problem now starts happening immediately after putting signal through it and doesn’t stop.
I took it to a local audio repair who thought it was a relay issue but was unable to fix it after several tries. He referred me to another repair shop who has now told me that 8 Mosfets in the amp are blown and the input selector has ’aged out’. To repair it would cost about $450 dollars as he would have to replace many components in the amp and that it would end up as a just a power amp since the selector is a custom component that Perreaux doesn’t sell anymore.
I’m trying to get my money back from the seller, but he’s pretty much refusing saying that this is impossible and suggesting that I must have overloaded it since it worked when he sent it out. One thing to note is that I have carpet (not deep, quite short) and the binding posts on the Thiels are at the very bottom where I imagine it’s possible that the carpet could come into contact with the connectors. I have 2 other amplifiers (an entry level Cambridge Integrated and a B&K receiver which is a MOSFET design) and neither have had this issue.
My question is: could static electricity or contact between the carpet and the binding posts/cable connectors cause the amp to fail? If so, how come it took 4-5 days? If not, what is the possibility that it is my fault?