Technical help selecting phono interconnect


I am currently in the process of selecting a phono interconnect for a tonearm rewire project. I intend to solder the tone arm wires directly to the interconnect and will be soldering the RCAs myself.

Up to this point i have been looking at Canare L-2T2S or Mogami 2549, both are 2 wire microphone cable with shield. This morning I stumbled on a tech paper on the Canare website that test and compares results of various cables.

Oddly Canare does not test the l-2T2S but it they include other 4wire variants. They do include Mogami 2549 and 2534 the 4 wire version.

So as a result of reading this paper I have concluded the following in terms of shield aluminum pet tape is best, then spiral wound followed by braided.

My question is regarding the interpretation of the results of the frequency response test, see page 10. The write up appears to me to contradict the charts. Point 2 of results states that 2 wire is superior to 4 wire, but the figures seem to contradict this. EG: figure 44, shows that Mogami 2534 curve remains flat at 0dbV further to the right the the curve of the 2 wire 2549. This is the same for all the graphs. You will note that there is typo in point 2, a key word is missing. What is the correct interpretation of the results?

http://www.canare.com/UploadedDocuments/A%20Technical%20Paper%20-%20Evaluating%20Microphone%20Cable%20Perfrmance%20and%20Specifications.pdf

One side note, despite using a balanced wire, my connection will be unbalanced, I intend on using one wire as the signal the other as the ground and floating the shield at the RCA and grounding to the TT ground wire. If I were to choose a 4 wire cable how would I wire it in an unbalanced configuration, do I simply double up on the signal and ground?
nick_sr

Showing 5 responses by williewonka

Nick - what cartridge are you using at present

What are your likes/dislikes

Cheers
If you are using a two and four conductor cable of the same grade from the same manufacturer - frequency response should be the same.

However, connecting the four conductor cable in two pairs will double the capacitance - this can effect the overall tonal effect the cable has on the sound

Connecting your tone arm wire in this manner could have significant effect on the sound, since capacitance is one of the variables often taken into account when matching a cartridge to the phono stage. From the specifications of cartridge and phono stage, it may appear to be a good match, but because of the capacitance of the cable they may not sound as expected.

Capacitance Is often overlooked in audio matching - e.g. Naim amps do not perform their best if used with a high capacitance speaker cable - and they used to state that on their website.

I've often read posts that report some interconnects sound bright or harsh - but it may not be the interconnect, but the combination of that interconnect with the attached component.

I now ensure all my cables are low capacitance to get the best neutral sound possible

So beware of capacitance
Nick - true - the frequncy response is "better" for the 4-conductor cable.

But those response curves are for 100 meter cables - the response curve for a 1-2 meter cable would be completely different.
Mesch - I have the Cardas one-piece tonearm wire that I find very good for phono but I don't know the Capacitance

For Interconnects I use the Van den Hul D-102 mkIII as a becnhmark which is rated at 37pF/meter

For speaker wire anything below 30pF suites MY AMP

NAIM actually states on their web site...
- 1.3 - 1.5microHenries per metre (Loop)
- MAX 20picoFarads per metre
- About 25 milliOhms per meter (loop)
- MIN Length 3.5 metres

I use "low capactance" as a guideline, in that too much capacitance in cables may effect the sound

I don't think I would state that all cables should be low capacitance across the board for everyone :-)

For phono it seems to be the case, BUT it REALLY DOES DEPEND on the components you are connecting
Nick the 102 mk III is 37pf/meter - but the later versions are 61pf/m

http://www.vandenhul.com/products/cables/the-d-102-iii-hybrid-halogen-free

The card as rewire is around 60pf/m and is considered low, so I think 125pf/m should be fine

Be sure to post your findings for all :-)