2. analog
  3. 1308608139

Nitty Gritty 1.5Fi vs. VPI HW16.5vs. Okki Nokki

I've been back into analog for about 2 years. As I've resurrected a lot of old vinyl and purchased a lot of used vinyl (Half Price Books, lot sales on Audiogon and other sites, etc.), a record cleaning system better than my present Spin-Clean has become a necessity.

Spin-Clean does a decent job but, with some but by no means all of my records, there is a lot of surface noise that is left behind. I presume that this is due to residue that results from the surface tension of the droplets of fluid left behind after the record is dried (either by air or by using the supplied cloths), or, less likely, the attraction of microscopic particles to the [still slightly wet] record surface as it dries, and which cannot be removed by pre-play record cleaners (i.e., Audioquest brush, Discwasher, etc.).

Why surface noise is audible on some records more than others could be due to many things--the cut and modulations of the groove, mold release chemicals, etc., etc. Also, it can vary from one side to the other and from one track to the next in the same record.

I'll mention that I only use the Spin-Clean fluid, and mix it with distilled water in the proportion recommended by Spin-Clean.

All of which I mention because it speaks to the necessity for some form of vacuum cleaning.

I'd like to open up to the forum re any preferences in the above named field of machines (or any others which any forum contributor deigns to recommend).

Also, could there also be a cheap'n'cheerful alternative to any of the above, such as the KAB record cleaner and a canister vacuum, used in conjunction with the Spin-Clean? I know I'd have to spin the record manually and deal with an external vacuum source, but at a third of the price, it merits serious consideration.

In any event, I welcome the forum's esteemed opinions.

Thanks, John
128x128distant_replay
nax's avatar
nax
2 posts
 
You stated that on some of your records that you clean with Spin-Clean but by no means all of them there is surface noise left behind. If there is noise left behind then either the records that noisy after cleaning either have needle damage done to them or perhaps they where cleaned prior to the Spin-Clean with a cleaner that left a coating of something on the disc that the Spin-Clean was unable to remove in one cleaning. It is also very important to have multiple drying cloths on hand in order to thoroughly dry the records after cleaning and to make sure that you are using the proper number of caps of fluid per bath,
4 oz bottle uses Three Caps Full of Fluid Per Bath and the 32OZ bottle only uses one. There are also a lot of people who use the Spin-Clean for Cleaning and a Vacuum unit to dry because most of the Vacuum units use an alcohol based cleaning solution which can be detrimental to the vinyl.
theo's avatar
theo
2,684 posts
 
I also sold my Nitty Gritty years ago for the 16.5 and am so ahppy that I did. I did get rid of the VPI plastic nut and bought a TW weights record clamp that works great. The 16.5 is a simple but extremely well built machine that should last for years. I recently did some mods that should help it last even longer.
distant_replay's avatar
distant_replay OP
10 posts
 
Thanks for the response. Truly awesome system, BTW, one of the best I've seen on Audiogon. My system is - uh - a bit simpler - Naim, Rega, Spendor. I've been toying with the idea of moving away from the Brits (say, Maggie 1.7's, obviously with different amplification).

But I was underwhelmed when I heard a dealer demo (and this with mid-line ARC gear, hybrid linestage and CD player and SS amp). Last I heard, ARC at any price level is a few notches above my Naim stuff.

Yeah, it had all of the Maggie virtues, but the tonal balance screamed THIS SYSTEM HAS NO BASS!!! To be fair, speakers and wires weren't quite broken in (and the dealer was using Nordost wires, Blue Heaven, I think). IMO Nordost flat wires tend to be a bit thin sounding with planars; if I had such a system, I'd try a Cardas.

I do use Nordost flat wires (Red Dawn) in a second system, which alternates between a Fisher receiver and a McIntosh 1500 (modified by Richard Modaferri to use 5881 output tubes; the Fisher uses stock 7591's), driving some little B&W's I bought ~10 years ago. Within their context, they sound wonderful.

But, all that said, I just keep gravitating back to Brit-fi.

Finally, thanks for your opinion; I'm leaning towards the VPI and have all but eliminated the cheapie option.

Best regards, John
rockitman's avatar
rockitman
417 posts
 
The Okki Nokki is about the same cost as the VPI, better Built (all metal construction) and has an auto shutoff if waste fluid resevoir is filled. It's really a no brainer for the money. I wouldn't touch a nitty gritty
miner42
709 posts
 
I have owned a NG 2.5Fi and MiniPro. Both are exceptional cleaning machines. VPI 16.5 just seemed a bit 'cheap' quality to me.
More to discover