New Cartridge Causing Intermittent Popping


Vinyl Experts, I need help in diagnosing a problem. 

Before this last weekend, I had three (3) cartridges in my stable:  Kiseki Purpleheart, Dynavector 20x2; Benz Micro LPS.  None of these carts made any significant popping noise. I gave an AudioTechnica ART9 to a good friend last year. That had no such popping noise issue either.

This weekend I installed a brand new Goldring Ethos MC cartridge.  It sounds glorious out of the box and is opening up a bit. Very seductive sounding pickup. 

But the Ethos is exhibiting intermittent yet consistent popping when playing all sorts of clean, excellent shape vinyl.  The popping is as loud as the source material and disruptive.  It comes with no notice, stops and starts up with a single pop every so and so. [I haven't timed it].  I can, however, sometimes get through a side with one or no pops. For the most part it is still there. 

I setup the cartridge with my Feickert protractor.  Pretty easy setup compared to my other carts. 

Some aftermarket Jelco headshell leads were a touch a loose where they affix to the arm.  I tried crimping them down but to less than perfect status.  I've ordered new ones to see if that is the problem. 

I've never had any noise issues with my Manley Chinook phono preamp. The lion's share of my collection sounds just great with it until this issue arose. Most of my records that are in excellent shape do not exhibit snap, crackles, or pops unless you crank the volume during a very quiet passage--and even then they are not easily audible. 

Goldring says the following: 

Load resistance
100 Ω
Load capacitance
100 - 1000 pF

Playing weight

1.5 - 2.0 g (1.75 g)

This cartridge sounds wonderful--especially for the price tag.  I really want to fix this  small but annoying issue. 

Advice? 

Setup: 

Source - Technics SL1200 GAE

Phono Preamp- Manley Chinook

Integrated Amp - Marantz PM KI Ruby

Thank you folks!  Solving this is a priority for me. Your help is greatly appreciated. 

128x128jbhiller

Showing 3 responses by yogiboy

It might be the stylus design!!

Line Contact / Linear Contact / Special Line Contact / Fine Line

The cross-section of a Line Contact stylus can be regarded as an Ellipse taken to the extreme and with straight vertical edges (rather than round) for deeper groove contact, as illustrated below.

The Line Contact stylus shape can be considered a later variation of the Stereohedron stylus (with its four slivers shaved off, it is sort of a double elliptical) as patented originally by Pickering in 1973.

Patented in 1978 in Japan by inventor Junshiro Ogura, the Line Contact stylus is shaped such that it allows maximum vertical contact with the groove walls whilst having a small front-to-back contact. This kind of stylus is almost always fitted with a nude diamond. Compared to Conical Styluses (that due to their rounded shape only touch the groove walls in one vertical spot, thus more easily wearing them out on that depth), Line Contact styluses can make slightly worn records (when worn as a result of the use with conical or elliptical styluses) sound almost pristine. This is because the larger vertical area can now be modulated by previously untouched areas of the groove walls.

The variations such as Linear Contact, Special Line Contact, and Fine Line all represent further refinements of the principle, usually adjusting the shape of the shank and/or the width of the contact area. The variations with the narrowest contact area such as Ortofon’s Fine Line, Audio Technica’s Line Contact, and the more generic Special Line Contact achieve the most accurate results with the best high-frequency response and lowest distortion. All the variations have in common that the stylus wears more evenly which results in a longer stylus life.

In general, the more precise the stylus shape, obviously, the better it is at picking up high frequencies but also the better it is at picking up small defects in the pressing or very brief noise spikes. Compared to the simple Stylus shapes, the Line Contact and more advanced designs require records that are cleaner and in better condition to be played mainly noise-free. But in my book a little playback noise here and there certainly does not stand in the way of my musical enjoyment, and even if so, usually, it’s nothing a record cleaning machine can’t fix.

It’s that fine line stylus on the Goldring. It goes deeper in the grooves than your other cartridges!

Good luck with that. I still think the problem is with that fine line stylus going deeper into the record grooves. You will find out with the exchange. Let us know!