Is the "standard" Linn Sondek LP-12 surpassed by newer turntable brands and designs??


More than ever, the infamous Linn Sondek LP12 turntables appear for sale on Audiogon. The price of each piece varying based on the age, condition, and how many authorized factory upgrades have been done .

The question is: Is the "standard" ( without any upgrades) Linn LP-12  outperformed by newer brand turntable designs??  It seems to be getting long in the tooth as a viable high end turntable

Can someone explain what made the sound quality of this table so special and so sought after??  Is  a USED standard Linn LP-12. really worth the money??   Thanks 

sunnyjim

Showing 5 responses by moonglum

Dear Jim,

I cannot comment on the current base level LP12 but I can describe "used" versions of it (and if you are interested, comparisons between the ultimate maxxed-out Linn LP12 vs other top-level turntables)

Like many I formerly owned a 1980s Valhalla-ed LP12.

Idiosyncracies aside, IMO, it is a very musical turntable . The sound is distinctly different from more “neutral” sounding T/Ts such as the Clearaudio & VPI ranges and those of similar design. Bottom line is that if you had been an LP12 user for decades you would find the sound of those tables unrewarding and unsatisfactory (and, dare I say, almost boring ;^).

The Linn has an ability to vividly render the music. Low level detail is similarly vivid and accentuated in a way that doesn’t happen with those other tables. For those of a more puritanical mindset, the Linn is not technically or dynamically correct but it isn’t something many would find objectionable, even if they were aware, and it’s unique sound can make most recordings exceptionally entertaining.

To cite the example of Arthur Salvatore. According to his own reports, he had one for a short time, got rid of it, then later purchased another because (I’m guessing) he wasn’t quite sure what he was missing but was probably convinced at the time he was missing something! :D

Since then he seems have fully-formed an opinion but quantifying the LP12 sound can be an elusive process.

(I should also state the disclaimer that I don’t necessarily subscribe to any particular person’s views on the LP12 but accept that they have their own opinion)

The Linn seems to perform particularly well with its own ancillaries (Ekos/Ittok and Linn carts) and can also be enhanced by using those in conjunction with Naim pre-amps of that era e.g. NAC32.5. Bearing in mind that the Naim’s integral phono PCB was handling a signal little greater than 100 micro-volts the results were staggeringly good compared with expensive and highly rated SS stages from other manufacturers, which could appear artificial and “reproduced” (or “unnatural”) by comparison.

BTW, the pedigree of the NAC32 line can be traced back to the days of the legendary Linn/Naim/Isobarik tri-amped systems of the 70s. Hearing that setup for the first time could be categorised as a memorable Hi-Fi milestone in the same way as one’s first exposure to the Quad ESL-57. It was a game changer that had profound effects on the industry for many years to come. In fact Linn’s market presence was so powerful that alternative designs such as Oracle & Michell had great difficulty breaking through because nearly every hi-fi publication was pre-disposed to recommend the LP12 above all else!

If one was seeking musical holograms or 3D living musical sculptures then this was one way to get them.

Of course these results hinged on the Linn being pampered and treated to its own dedicated and tailored mechanical support (allied to mounting that support with perfect stability on a solid concrete floor). In this regard it is even more critical than many other current suspended sub-chassis designs. Poor attention on the part of the user to this particular detail can make the LP12 sound quite ordinary. It is a design where such fastidiousness is rewarded.

(Note : Contrary to claims the suspension doesn’t drift “out of tune” if it has been properly set up and you elect not to have it adjusted/re-tuned every few years.)

So what you have here is something that, in its way, can be more “addictive” than almost anything else out there but there must be a willingness to pander to the forementioned details. You should also note that, long ago, Linn discontinued support for the Valhalla PSU. If a replacement is needed then the Hercules II is the recommended alternative (and usefully also gives it switchable 45 RPM capability).

With the latter you will have to crank the startup by hand i.e manually spin the platter to help it up to speed but to a much lesser degree this was always the case with the Valhalla. Once there it’s fine.

Hope this "sojourn through the archives" proves helpful ;^)

Dear Jim,

It is a popular and understandable misconception that the Linn is a "tweaker's dream". The fact is that once you have settled on a basis (such as the Valhalla, perhaps with the glued rather than spot-welded sub-chassis) then no further alterations are required.

"Setup" means exactly what it says : once the turntable is properly established in your listening room no further action is necessary.

In this regard the LP12 could actually be less troublesome than most others. For example, main bearing lubrication does not require service. It is a once in a lifetime exercise (only in the unlikely event that the previous owner spilled the contents of the Bearing Well in transit!). Many other turntables require you to re-lube every year - which I find a PITA by comparison.

The Linn's mechanical parts are unburstable and will last for as long as you want to keep the turntable.

Although I appreciate the enthusiasm for old Garrards, rim drive never held any appeal for me, perhaps from my tape-enthusiast standpoint ;^)


If you wish to fully experience the depth of feeling for the LP12 you should take a trip over to PFM and you'll get vastly more information there.


Interesting Nandric. It's not an occurrence I've ever heard of but consulting the web shows it has happened. It's important to note that the oil in these cases isn't emanating from the bottom of the well but coming from the top. My guess is that the bearing's either been overfilled or tilted in transit causing a spillage at the top of the bearing collar. Putting less in should cure it.

Unfortunately, in this regard, a popular technique was to deliberately overfill then let the bearing's descent push excess oil out onto the top plate, then remove the bearing briefly to wipe off the excess.

Messy. ;^)

Dear Jim,

You have my sympathies. Picking up on the subject of tyre kickers. There is no doubt that there was an element of snobbery or superiority complex amongst those who were part of the Linn "revolution" at its peak. It started from the Chairman then flowed down through manufacturing & support then through the Dealers, eventually affecting the media and finally many of the customers. It was like a cult, not dissimilar to the current analogue industry in fact.... ;^)

(An industry which I confess to occasionally over-fervently defending throughout the years when faced with the onslaught of digital ;^)

Despite being a Linn owner at that time, I found the arrogance of  some Linn Dealers irritating in the extreme.

BTW "PFM" is shorthand for "Pinkfishmedia" forum.

You need to get out more. ;^) :D

SunnyJim said:

"The question is: Is the "standard" ( without any upgrades) Linn LP-12  outperformed by newer brand turntable designs?? It seems to be getting long in the tooth as a viable high end turntable".


Davey has made an important point. If the OP considers an LP12 "long in the tooth", how much more so a 1960s Garrard ;^)


To extend the spectrum of views on the 401 consider the opinion of experienced user "Paskinn" (scroll down to the bottom of the page) :

http://www.pinkfishmedia.net/forum/showthread.php?s=5af14203b2e7b0f5869af666496c6de4&t=122182&am...

Now you have a balanced profile Jim, the Good, the Bad & the Ugly ;^)

When it comes to turntables they all sound different which means that they are all (technically) inaccurate.... :(