how can I find the polarity out from my XLR

ths to everybody here for your help; it's realy great !
yesterday I'd try to check simply with a digital multimeter but it doesn't answered to MY question ..

Maybe I'll have to use a ocsillo ;-( ... but I've to find one first

I'll open my cdp and have a look inside

thanks again

laurent

As I recall, the earliest version of the Sony SCD-1 had pin 3 hot, but they did come out with a later version. One of the changes was to make pin 2 hot.

A lot of European gear is pin 3 hot, especially older pro audio gear... your pinouts are probably correct on the back of the Sony and not what the user manual says...

Just ignore it. According to statistics, 50% of all CD's are recorded in wrong polarity anyway.

You really need a 'scope to double-check this. However sometimes there is a slight DC offset voltage on pins 2 and 3 from some cd (or DAC) XLR outputs. If you have a DVM with reasonable resolution you could try and measure on a low DC volts range across pins 2 and 3 and then reverse the probes and compare. This may give you an indication as to which one is "hot".

If you try this, usual dis-claimers apply! Regards, Richard

> GMC
yes I'd email my problem to Sony ... waiting for the reply

Have you contacted the manufacturer? 9 out of 10 times, they mis-print the manual.

> Twl
What I'm sure is that I don't know what is going out of my CDP ;-)

my user manual of my CDP says connectors are :
1=ground
2=(+)
3=(-)
and back of my CDP connectors are explained :
1=ground
2=(-)
3=(+)

so I need to check wher is my (HOT) pin

do u understand what I mean?

sorry for my english I'm a poor frenchie guy

Disregard my post, because I mis-read your question. I thought that it said your polarity was different from the CD player to the preamp. Sorry.

> Ivany
hi,
my only problem is that I have to give to my 'DIY cableman' the right polarity out of my CD player to match with the polarity 'In' in my preamp
I know the polarity In of my Preamp (1,2,3 pin are ok it's an US Cello Encore)
but I've a doubt about (+) pin out of my CDP ( I'm not sure (+) is out of pin 3 it's an european Sony player)

Try changing your speaker cable connections at the amp. Move the (+) to the (-) and vice versa.

If the sound improves substantially, then your XLR connections (or some other connection) are reversed polarity.

I can only say that it is unlikely that the manufacturer went through the trouble of having polarity labels made, only to have it be wrong. So you can be 99.9999% sure that the polarities on each machine are as they say they are. You can check the polarity of your interconnect cable, by using an Ohm meter and verifying that pin 2 on one end is actually wired to pin 2 on the other end. The same for pin 3. If they are, then you have incorrect polarity on your system, and you have to match the polarity. The way to match the polarities from one to another is by reversing the polarity of the leads in one XLR connector on one end of your balanced interconnect cable. This involves removing the barrel of the XLR connector and de-soldering the wires from pins 2 and 3, and re-soldering them in the reverse configuration. Leave pin 1 alone. If you can't do this, take the wire down to a good technician, and have him do it for you for a few dollars.

ths chichiuno,
i'll try both methods..
but maybe the 1st will be dificult because my Sony SCD-1 (my CDP) is FULL inside ; I'm not sure I could have a look inside ;-)

try this and be back soon

Laurent

Others will tell you how to figure it out but after you do, a tip.

If you have to change polarity on the cable, do it at the source end. This is because the signal cables are often different from the return wires; you want both signal wires to be the same no matter what config you end up with.
If you have sealed cables send them to the manu and they will do it at a nominal charge and they will still be factory.

pop the cover of the machine see what color wires go to wich pin, or use a digital multi meter with a cd in the machine playing, probe the - and the + and the meter will confirm polarities