Hi all, I have a dedicated AC line for my audio, Monster 5100 filter, Quantum symphony conditioner, Nordost Red Dawn interconnects, MIT T2 biwire cables(15'), MF cdpre24, PS audio amp, MF tube buffer, Emminent Tech speakers, When I put ear close to the speakers I can hear what sounds like something frying in a pan, sort of a crackling sound. It is louder through the left speaker than the right. To make things worse for about two days the left speaker was absolutely silent, with the right speaker only emitting the noise very lightly. I have removed, and relocated all the devices but when the noise is present it stays. I tried rerouting the cable, even lifting them up off the concrete basement floor, but no help. I unplugged the tube buffer, no help. All the equipment is mounted on a verticl rack. I have moved the tube buffer away from the rack. Even with all the lights out I still have it. But then sometimes I don't. When the noise is gone I tried to discern what was different but could not. Does anyone have any ideas? Thanks
Thanks again everyone for your responses. Golden Ears I think you are right about not worrying about it too much. I am pretty happy with the sound the system is providing me. It is the best I have had to date. It was just one of those things that you can get carried away with trying to eliminate only to discover that in the end it really didn't make any audible difference when sitting in the listening position. At first I was a bit concerned, but now that I am sure it's comming from the tube buffer, well I can live with it. I suppose it might be covering some low level detail, but I really can't discern anything. Perhaps the background would be blacker, who knows. I like the way the system sounds and that in the end is all that matters. In a few years I will probably get the upgrade bug again anyway!!
Hi, I think the really important part of this "problem" is that it may not be a problem at all. You said:
" When I put ear close to the speakers I can hear what sounds like something frying in a pan"
If you had to get that close to the speaker to hear it, and if the noise does not increase when you turn up the volume, then don't worry about it. Just about every amp, tube or transistor, can send a little bit of noise into the speaker. Tubes always send a little noise, that increases with age, which is one of the things that can tell you when to replace them.
Wow,that stinks.I had the buffer in as you did. My buffer is long gone now but I wouldnt get another one. I have a tubed SACD player now, so I doubt I would get any benefit from one. It made my old Sony SACD player sound better in some aspects though.
Well I disconnected, then reconnected everything while listening in between. I discovered it is the Musical Fidelity tube buffer causing the noise. I called the importer and spoke to a technician. He told me that I should not connect the buffer between the pre-amp and amplifier. He reported that doing so could cause damage to my speakers and/or amp. The reason is that when the buffer is first powered up a DC spike is created that is passed through the output of the buffer. If the amp is already on this spike could damage the amp, blow a fuse, or blow out speaker drivers. The tech recommended mounting the buffer in the tape loop of the CD Pre24. I did this, and found that the noise I was getting through my speakers was almost completely eliminated. The left speaker is now dead quiet, while the right has just a hint of noise with the volume set medium high(which is about the limit for my room). I also noticed a little more freedom in the area of dynamic shifts from the amp. This was confirmed by viewing the amp meter on my line conditioner. Without the tube buffer the music is clear,detailed but a bit flat. The buffer adds that bit of livelyness to the sound making it sound more real. Therefore I will continue to use it. On my system the bass does not seem to be adversely affected. Thanks to everyone for their help.
Thanks David99 for the input. I will check my bass with and without the buffer. I do think the buffer adds a wee bit of depth to the instruments, as well as a tad of warmth, but I may need to rethink if it turns out to be the source of the noise. Newbee, I will do as you recommend and isolate each component. I did not have a chance to remove the tube buffer yet. It's funny but for the last several days the previously noisy left side is absolutely quiet, while the right side still has a bit of crackle. I will post my findings after I have isolated everything.
Dougm, Sounds like taking the buffer out didn't make a difference. I can't tell from your post if you have done this yet, but if not....Disconnect everything in your system (cables and IC's) except your amp and speakers and see if you have the "sound". If you do you have at least isolated the problem to your amp and/or power. Then work backwards thru your whole system one component at a time, very methodically. For example add your preamp and IC's to amp - and listen with out turning it on. No "sound", now turn it on. Also rotate selector switch before adding Ic's from sources and listen. Repeat process until you isolate the noisy component. Then feed back.
I had the MF tube buffer in my system for a while. It improved detail and was smooth but it smeared the bass. Thats one reason I sold it. The other,it was noisey,hiss,crackle,pop.I switched out 3 different pairs of tubes with no success.
Hi Marty, I really don't know if it is AC. The reason I went in the direction of it being due to the tube buffer was because that was suggested to me by someone who works for a line conditioning manufacturer. Do you have some experience with RFI making that sort of sound? I would appreciate any help you could give me. thanks
Hi Newbee, Someone else had suggested that it could be from the tube buffer. I did unplug it, but it was still connected between the preamp and amplifier. I will take it out altogether and see if that helps. thanks
You must have a verified phone number and physical address in order to post in the Audiogon Forums. Please return to Audiogon.com and complete this step. If you have any questions please contact Support.
