Help I have a radio in my tweeter

You have RF interference leaking in somewhere to your system. The likely culprit is usually in your cables.

I have owned gear that did the same but for me its mostly been solid state amplifiers.I could find no way to reduce or eliminate the problem except replace the amps.If your in a hi RF area or near broadcast antenas your out of luck.

Wonder if you have a "Ham" amateur radio operator in your neighborhood? Sometime if they don't adequately shield their transmitter you can pick up the "transmissions" through your equiptment. If it is a "ham", and you can determine who it is, then "they" have to take the steps to keep their transmissions from "bleeding" into other peoples equipment (stereos, radios, TV, ect).

I used to pick up a HAM radio signal in my tube system. He was a block away with way too much output (according to someone who knew him). His voice came thru my stereo as loud as any instrument! Perfectly clear! The FCC did nothing when I called them. Maybe this is what is happening to you...

Sorry guys, but most of the time it's the audio gear at fault when it picks up a radio transmission, ham or otherwise. As long as the transmitter is operating legally (and most hams are sticklers for this) it's the responsibility of the audio owner to solve the problem, though most hams are happy to help.

Much audio gear is built with inadequate shielding and bypassing, which allows RF to penetrate and overload the circuitry. Use of exotic poorly shielded interconnects doesn't help either.

That's why the FCC did nothing when Philjolet called to complain.

I hold a ham ticket (WB5KKO), though I've been inactive for many years, so I know both sides of this problem.

ghostrider,

they told me they were underfunded and was told the guy had an overpowered rig. I moved soon after so it was not a problem...

Itball,

In any case, if it is a "Ham operator", and you can find out who it is, go talk to the guy. Most of the time, if there is a problem, they will try to help you find a way to take care of the interference. Truth be told, most "Ham operators" are good guys (and btw, quite a few of them are into audio equipment, especially tubes).

Thanks for all your responses.

It doesn't seem like a HAM issue - I can make out enough of the detail such that I'm fairly sure it's a radio station. But it does come and go - have not heard it since this morning.

Hmmm...

I've also had this problem.... and the guy who sold me my speakers/cables had it too. Some ers cloth wrapped around any exposed connectors helped a bit. This problem is a real pain - you have my sympathy.

In the field of pro audio where I make my living, this comes up regularly. The trick is to give the RF a place to GO, besides the next stage. There are many ways active electronics can demodulate, downconvert, and heterodyne with RF emissions that get caught up in open circuitry. Also, some exotic cable designs give up shielding for the idea of supposed lower impact on the musical signal. Here are a couple of tricks I have in my bag:

Move your gear a few feet! RF energy pools like invisible currents of water, with nodes of dead spots and peaking stronger areas. There is a chance that multipath can work for your here, and you can find an arrangement that will kill the radio show, in a cancellation node (the fence board part of the "picket fence"). Moving cables around can help.

Try different cables. Start with a cable with a clear design goal of minimizing external influences, that has a solid shield, braided, with a drain maybe, or even foil and a drain. Stay away from twisted pairs and no shield. Unplug and plug in all of your connections; some patina/corrosion can act as a crystal set to demodulate AM broadcasts.

Buy clamp-on RF chokes. They come in several shapes and sizes, and can reduce the effectiveness of your cables as antennas. Try them on your power cord or input/output cables.

Buy some ceramic disc capacitors. If you know your way around high voltage circuits, bypass power supplies, high impedance stages, and inputs and outputs with values ranging from a few hundred pF to 0.1uF. The idea is to provide an alternate path for RF energy away from the circuit that is demodulating it, without impacting baseband audio below 20kHz. These parts should ALREADY be in your gear. There is a chance that a lead or solder joint on a cap has failed, as indicated by the fact that only one channel is affected. If you're not so sure what is running at 90V to 350V in your tube gear, don't mess with the insides (for your safety), just try the external connections.

Lastly, double check for tight screws on the chassis. Again, sometimes a little corrosion takes on the form of an oxide that acts a bit like a diode. Unscrew and retighten all fasteners that go to PC boards, ring terminals, and metal parts.

Good luck!

:)

Well, I have a tweeter in my radio!!!!

Wait! They both go great together...