I think the Flux is the same as the Hudson, and while it vibrates, it certainly doesn't do so at U/S frequencies (>20kHz).
I'm currently experimenting on older cartridges with the Humminguru S-Duo, which combines a stylus VTF gauge with a proper U/S (only 40kHz I believe) transducer.
|
My initial experience with the S-Duo:
Firstly, the scale. The instruction booklet does not mention that there is a clear plastic protector over the scale pad, and it is actually hard to see. Until you remove it you will be convinced the scale does not work. The scale reads the 5g test weight as 5.05g, and taking the weight off and zeroing it makes no difference, it still reads 5.05g. Comparing it under a stylus with my existing gauge shows that it reads 0.05g high too. I'll just have to remember that.
Secondly, the U/S cleaner. This comes with three rubber rings and you are supposed to fit one into the well where the cleaning happens, and select the one that lets your cartridge rest its body (not the cantilever) on the rubber ring with the stylus so positioned that it will dip into water placed into the central well. All three rings are the same thickness, and vary only in the size of the aperture in the middle. If your cartridge has its VTA set so as to be slightly tail down it will be hard to do this without getting the bottom of the cartridge wet! It turns out to be critical that the water is dripped into the well to exactly the right level. You don't want moisture inside your cartridge! I put some distilled water into a fine dropper bottle and then tried the cartridge - and had to suck out some water with the tiny pipette provided. It might be better to place the cartridge onto the rubber ring, then add water a drop at a time until the stylus only is in the water. There is only a couple of drops of leeway before the base of the cartridge will get wet, and did I say you don't want water inside your cartridge?
The next thing to be careful about is that by this time the device will have switched itself off, so holding the turntable motionless, you press the power button until it turns on (it may take several tries) and then press the button that starts the 20 seconds of U/S cleaning. Then lift the tonearm, and check the underside of the cartridge, dab off any water - you know why by now. I dried out the S-Duo's cleaning well with a tissue, as the foam drying pad provided won't fit once the rubber ring is in place.
Phew! I have had less stressful times changing cartridges and setting them up. Water and hardware within millimeters of a stylus, not to mention wiping with tissues. This is not a thing I will do on any regular basis, but only if there is visible gunk on a stylus that doesn't come off with a brush. My main way of keeping my stylus clean is to keep my records as clean as possible. After that a little carbon fibre stylus brush gets used, very gently and carefully, daily. I did buy a Hudson "ultrasonic" but it isn't ultrasonic, vibrating rather coarsely at, I'd guess, 100Hz. I think that is more likely to damage a stylus than actual tiny amplitude U/S vibrations. I'll note I didn't see any bubbles in the cleaning well, and I'm inclined to try an experiment with some detergent, distilled water and NO stylus. I just did it, still not a bubble, even if I dipped the tip of the pipette into the water during the 20 second run. Maybe I'm wrong to expect anything - after all, the 120kHz transducers in my Degritter (which will certainly make foam with detergent in the water) are a lot more powerful than the tiny 40kHz transducer rumoured to be in this unit. One cannot hear or feel anything when it is running. If it were a lot cheaper I'd take it apart to see what is actually inside it. Another thing to add to the list of hi-fi items I wish I could send off to Big Clive on YouTube and have him reverse engineer them!
|
Don't forget to consider the amplitude of the cleaner's vibrations. My Hudson, be it vibrating at my estimated 100Hz or your reported 222Hz, has vibrations that wiggle the stylus and cantilever considerably. Way more than a record groove could.
The S-Duo makes such fine amplitude vibrations that the cantilever does not move perceptibly. Now what I do not know is how the epoxy or whatever holds the stylus on to the cantilever will cope with either kind of cleaning vibration. I would guess, and it is a guess, that tiny amplitude vibrations at 40kHz are less likely to destroy the glue than large amplitude low frequency—222Hz—vibrations. I suspect more force and larger movements are more damaging than small forces, and small movements at higher frequencies. That's why I'm experimenting with older cartridges and seeing what happens.
I do have a couple of USB microscopes, but I don't know where they are after a recent move. So, if Amazon and the seller do their thing correctly, I have a rather expensive USB microscope and stand (an updated version of Fremer's recommended device for SRA adjustment) on the way. It may be I shall be able to take some comparative pictures.
|
