2. misc-audio
  3. 1067549822

Electrical question re dedicated line

In my home situation(new house) the electrician who came by to install a dedicated line said it would be too difficult and very expensive. Another electrician said that I could have a dedicated line but it would be external and would travel accross the outside of my walls(insulated of course) and would have a little box for the receptacle outside of the wall on the wall. My question is that the fact that my system is on a circuit with it's own breaker, is that kind of like a dedicated line? The breaker my system is on has 4 seperate receptacles on it in my room but only my power regenerator(PS P500) is conected to one of those receptacles.In other words, all that is on the circuit that goes to the 4 receptacles in my listening room is my P500. The other receptacles are not in use. Is that kind of like a dedicated line? Would there be much advantage to doing what one electrician said was possible and have an externaly run dedicated line?
My system is :
Pass X250 amp
Pass X1 preamp
Talk Electronics Thunder3.1b CDP
Hales Transcenence 5's speakers
PS Audio P500 power plant
Shunyata Aries and Lyra interconnects and speaker cable
Prototype power cords which were not given a name but are good as I've compared them against Shunyata King Cobra V2 and Synergistic Designers Reference and much prefered the cords I have.
Any help would be valued. Thanks
128x128mitchb
mitchb's avatar
mitchb OP
336 posts
 
Newbee, I'm running my amp through the ultimate outlet section of the P500(non current limiting) and the rest of my gear, preamp and CDP to regenerated power.The amp sounds better through the ultimate outlet section than straight from the wall.

Muralman, There is no crawl space under my house which is why I'd have to run the line externally.

Peterd, No electrician in Vancouver Canada(that I can find) will install a ground rod. Something to do with ground potential and the possibility of a dangerous situation. I think it's just not to code here in Canada.

Hiend2, What's a dual phase line?

Thanks for all your advice,
Mitch
blptwp
40 posts
 
Hiend2
If you have 2 dedicated lines. Aren't you supposed to have them in the same phase ??
To have your gears in 2 lines in opposite phase is highly not recommended. I did this for a long time without realising it. After I corrected it, the sound is much better.
blptwp
40 posts
 
In N. America, the incoming 220 volts are split into (2) 110 volt legs in you main panel box and they are in opposite phase. Each of these legs also has other appliances (breakers) on them which add noise to the leg. If one of your circuts that feed your equipment is hooked up to one leg and the other equipment circut is hooked up to the other leg, then you are picking up the noise on both legs and raising your noise floor. If you hook up both circuits to the same leg in the panel box, you are only getting half the noise, because you are only picking up the noise on that LEG as opposed to picking up the noise from both legs.
In addition, you can avoid any noisey appliance breakers ( Like A/C, washing machine, fridge and furnace breakers) to the other leg that your equipment is not on, further reducing the noise on the leg that you are using for your equipment.
blptwp
40 posts
 
Further. If you have dedicated lines feeding your gears and they are plugged to the wall. You shouldn't need any power conditioner or power generator. If you do, you are adding another piece of electronics into your systems that will change deteriate the sound and you will hear the electronics too.
alrau1's avatar
alrau1
56 posts
 
Mitchb,

A dedicated line is one with no other devices on it. That's what you have, so long as you keep the other 3 outlets vacant. Save your money, or, if you're picky have the other 3 outlets removed and blank plates installed.

Peterd,

I once dealt with a guy whose job was investigating deaths by electrocution. He told me (from, ahem, experience) that separate ground rods can vary greatly in potential, especially during an electrical storm. It is a safety hazard to have some of your electrical appliances attached to a different ground source than the rest. Are you in a hurry to hear the stereo in heaven?
Furthermore, the NEC states that the ground conductor must be part of the same cable supplying the electrical box. In other words, you cannot run a 2 conductor cable for hot and neutral and a separate one for ground, but you can run 3 conductor Romex. If you have an electrical fire, good luck getting the insurance to pay for wiring that doesn't meet code.
More to discover