Component Upgrade/Mods to share?


Anyone done their own little component upgrades on their amps/pre-amps/CD transports/DACs/passive crossovers, and wanna share/report their results? I have been looking at Tantalum/Vishay/Holco resistors, non-inductive wire-wound emitter resistors, BlackGate electrolytic capacitors, as well as Teflon-Film capacitors, and drooling all over the place...

anyone?
atzen811
One of the things to look out for when parts swapping is that you know what value you are looking at. A resistor of say 1k ohms at 5% tolerance may be 1050 or 950 ohms. If the designer used his resistors based on measured values and not printed values, you may be substituting a precision 1%resistor of the wrong value. Sometimes it might make a difference and sometimes not. The same could be true for any component. The unit will still operate, but the sound might be degraded, or it may be improved. People that are experienced know which way to go when parts swapping. But, if you never do it, you will never get experienced. Sometimes you just have to jump in and do it. A good method is to try a part, let's say a resistor, that has a 10% tolerance rating. Not too critical. Get some precision resistors, some at the exact printed value, some a little higher , and some a little lower, all within the 10% tolerance rating. Try different values and see what, if any, difference in the sound may be. Also, the brand and type of these passive devices can sound different, so you may want to try a few different brands too. With caps, you need to get the right type and/or orientation or you're goint to screw up. Polarized, non-polarized, elecrolytic, film, etc., with polarized you must get the orientation right,by lining up the marked conductor with the place it should go. With some caps, particularly in power supply filtering, larger Farad ratings can be better, or even "piggybacking" additional caps over existing ones is common. Get some reading material and give it a try.
Twl is right on. The failure rate on parts is down right frightening. Most would rather have parts returned than to test each one to make sure that they meet spec. This despite the fact they give themselves rather generous tolerances. Some manufacturers (Dunlavy comes to mind) sorts and matches parts prior to manufacture and then indiuvidually fine tune each finished piece to match a reference model. AlbertPorter I belive the early Snells ( when Dr. Snell was at the helm)were treated the same way. Mixing and matching parts by reputation can be risky. I'll make another food analogy that will humour some. If one just follows a recipe with out considering the ripness (or lack there of) with out compensation they will never excell as a chef (it is chemistry and physics after all). IMHO fine tuning with lesser parts can yield better results than better parts with out fine tuning. While using the best parts and best skills should bring out the best (It SHOULD be easier too). It's more important whats comes out than what goes in. Unless you access to extensive test equipment and know how to use it, mods may be entertaining and educational,but not necessarily an upgrade. Another consideration is whether your work even, if sucessful is devaluing your initial purchase. Many people are turned off to purchasing self moddified used products. You may even void the warranty. With all that negativeity I encourage you to try. That's how this hobby started in the first place. It should keep manufacturers on their toes knowing that people are going to inspect their work and see if their getting their money' worth. Please share your decision/results with us.
I swapped out the cheapo mylar/electrolytic capacitors for axon polypropylene caps and those 12 cent resisitors with good non inductive ones.Also changed out the internal speaker wire as well in my small Klipsch bookshelf speakers.Made a vast inprovement in sound.
I have a PS Audio HCA-2 amp and replaced the dual runs of larger gauge Monster output wiring with quadruple runs of Jena Labs 18 ga. cryo'd wiring with outstanding results (everything better, no downside).

It was such a transformation for this amp that I started thinking about capacitors next. A guy on AA (Fiddler) used Black Gate caps on the four caps in the signal path and I made the same mod last week. Way too soon to tell what the final break-in sound will be like, but it's already doing things better than before (weight, low level information, decay, air etc.). The problem is it's still changing everyday. When you figure I've only added $130 to the cost of this amp with both mods and am now very happy with what I've got, the mods are a real cost-effective upgrade.
I am waiting for my speaker designer to get back to me with new values for Caps and Inductors. I asked those designers with experience with the particular drivers I am using to give me their opinions to which Caps,Inductors and resistors would work best.

After getting the vaues I will then switch out the caps first then the other parts as they breakin to see what effect are improving.

It is better to go slow on any changes that you are doing to make certain you are getting improved performance. Otherwise oyu might trip up the whole upgrading process.

I am experimenting with Cables also.

Good luck!