Why? Do you need to heat your house? Or maybe build up your biceps.
Seriously, putting even two Class A amps on a single chassis doesn't make sense.
Seriously, putting even two Class A amps on a single chassis doesn't make sense.
11 responses Add your response
Not sure what your budget is but, Cal. Audio Labs model CL2500mca is 500 watts per channel X 5. It runs in "Class A" for the first 100watts with 400 watts of head room. It's a digital amp that does not run hot and requires less power from the wall than conventional Class A or Class A/B because it much more efficient. Here is one for sale on A/gon for $3200 http://cgi.audiogon.com/cgi-bin/cl.pl?ampsmult&1073252587 Also, here is a web site with reviews and spec's on amp http://www.deregle.co.uk/frames/frame13b.htm Happy Hunting, Dave |
A digital amp is not class A at all - it is class D or higher. Gigantic difference in every way. The digital amps will not get hot, hence the 500W x 5. You could always get 3 2-channel class A amps! That would do it. YOu probably won't find any in one box due to obvious thermal issues, and if you do, I wouldn't buy it! Arthur |
I have to agree with Arthur. That is, an amp with 5 channels running at 100 watts RMS in Class A would melt the shelf that it was resting on let alone make the chassis glow !!! Having said that, i sincerely doubt if there is a multi-channel amp that will provide the sonics that you are looking for. As mentioned above, you'll probably have to resort to several individual amps that combine to give you the desired amount of channels. You simply can't cram all the support circuitry, power supplies and heatsinking for multiple channels with that level of sonics into one box. No matter what you do on a multi-channel amp, you're going to get cross-talk between the channels due to using a common power cord. This is true even with amps that use dedicated transformers for each channel. I don't know of any company that makes a 5 channel amp that uses 5 separate power cords. Sean > |
Sean...Digital amps (like the Carvers I just bought) are often described as having Class A, and Tube amp sonic characteristics. What is the basis for this? Perhaps the characteristic spectrum of harmonic distortion is similar. I am at the boundry of electric service by two utilities: Mass Electric, and Western Mass Electric. Would my channel separation be improved if I plugged one amp into each grid? |
El: Simulating tube sonics in a SS piece of gear typically means slower response times and less control of the drivers. This softens the leading edge of instruments, making them sound "less aggessive" or "more enjoyable" ( especially with typical digital recordings ). At the same time, you end up with a rounder, warmer bass. This tends to fill in the lack of body that many hard, cold and sterile digital recordings suffer from. Both of these are colourations related to poor technical performance but could be pleasurable to listen to. As far as the distortion characteristics of the amp go, i think that John Curl measured phenomenally high levels of distortion on both odd and even orders, making this more like a poorly designed Integrated Circuit ( IC ) based component than a tube or Class A design. While i may sound like i'm attacking / belittling these amps, the bottom line is that you like and are enjoying them. Who cares what i or anyone else thinks. Sean > |
sean...I have heard it said that conventional testing techniques get screwed up in ways that I don't recall, when used on digital amps. Who knows? "Less control of the drivers" means higher output impedance. That I can understand. But what does "slower response time" mean. Surely response time is defined by slew rate which is indirectly specd in terms of frequency response. HF response of tube amps is limited by transformer performance, and PWM digital amps do use filters to remove the switching artifacts, whereas conventional SS amps have to have a small inductor at the output to avoid becoming radio stations. So the digital amp may indeed roll off above 20Kc like a tube amp. It is the stated intent of the zr1600 designers to emulate tube class A sonics, and several reviewers have suggested that the goal was achieved. I don't have a set of 600 watt class A tube amps handy for comparison, so I suggest that you lay hands on one of these digital amps and see for yourself. The cost will be less than the wires to hook it up! |
El: many switching amps have gone to a design that uses a very high / fast switching frequency. This moves the potential for in-band noise of any measurable amplitude further away from reality. As such, some such designs offer excellent linearity out to well beyond 80 KHz or so with minimal distortion. If everything is done right, that means that the amp will have the speed to pass a square wave with good linearity up to at least 8 KHz. Anything above that frequency, in terms of musical notes or test signals, would be hit or miss depending on the individual design. Other units, with a lower switching frequency, lower hinge frequency for the filtering, poorer transient response, lack of stability with diverse loads, etc... tend to produce high frequency roll-off and in-band phase shifts at frequencies that are closer to mid-band reproduction. My guess is that you personally know all of this, so we are pretty much discussing this for the edification of those that aren't as familiar with such things. : ) Sean > |