2. amps-preamps
  3. 1133009082

300B tube death question........


Has anyone experienced the death of their 300b tube? What happened.....Exploded? Imploded? Awesome fireworks display? I'm just preparing myself for when it happens.

Also, the 300b tubes in my amp is underbiased and it won't reach optimum recommended voltage settings (volt meter should read 700ma but tube is at 450ma). The amps have manual bias adjustments only.

So far nothing has happened and the sound is fine. Should I replace them now or wait until they die? (see above question).

Amps: ASL monoblocks SET amps - (2) 300b per channel
Tubes: Valve Art 300B 98C

Thank you for sharing.
dogpile
8 responses Add your response
johnk's avatar
johnk
1,975 posts
 
Ive had one 300b fail it went microphonic.Had many other tubes fail no problems just replaced tubes
swampwalker's avatar
swampwalker
5,138 posts
 
NO return on a defective tube makes them a non-viable supplier, IMO. Sounds like they are using their customers as QA/QC. For 20 bonus points, what large software supplier uses the same business model? Seriously, unless your vendor is 30% lower in price than the competition, then their policy in unsupportable.
dogpile OP
118 posts
 
I think I'll just replace the one tube since the other three are still low hours. The place where I initially bought them cannot take returns which SUCKS! Goes to show, even tubes advertised as NEW can have low emissions. I'll search for a different supplier, perhaps Conus in Canada.

Thanks guys!
herman
2,253 posts
 
"HERMAN - Three out of the four can bias to 700 no problem. The one at 450 is the same brand and was purchased new."

Ah Ha, that would have been nice to know up front. You knew one out of the four was different but didn't share that with us.

"How will I know when a 300B tube is on it's last legs?"

You now know, you have a weak tube. It has low emmission. You have 2 choices, replace the one weak tube or the whole set. If they have relatively low hours I would replace just the one, but if they have a lot of hours I would replace the whole set.
dogpile OP
118 posts
 

SWAMPWALKER - Even when the pots are turned to maximum, bias will not reach recommended 700. I know it's the tubes because I tried different positions and it followed with the same results.

HERMAN - Three out of the four can bias to 700 no problem. The one at 450 is the same brand and was purchased new.

MARAKANETZ - Problem is just with the one tube. I know it's not the amps.

How will I know when a 300B tube is on it's last legs?

Enen though the music is still there (little degradation sonically), should I continue using this tube or replace it immediately?

Thanks again.
herman
2,253 posts
 
Has it always been this low? If you used to be able to get 700mV and it has dropped down to 450mV then the tubes may be fading away.. It could be something else but the tubes would be the number one suspect. The easy test is to try a fresh set of tubes but that is a bit expensive.

If it has always been 450mV maximum then something else is going on. Are these the tubes that came with the amp? If not, since all 300B tubes are not the same, these might not be a good match for your amp.
marakanetz's avatar
marakanetz
5,473 posts
 
...something is wrong even besides tube(s).
do you have this problem on both tubes and both channels?
swampwalker's avatar
swampwalker
5,138 posts
 
If you are saying that you cannot get the bias reading high enough, even with the pot turned up all the way, then something is wrong.
Log in to respond
More to discover
80x80
Krell Theater Amplifier Standard
80x80
Audio Mirror Wave
80x80
Allnic Audio H10000