tls49
Responses from tls49
| Subwoofer for "seamless" integration with Zu Druid Would you care to list the rest of your system, amp, source, cables? | |
| Dynaudio Focus 110.....Integrated amp???? Another thought about damping factor is that if you do the calculations to see what damping factor is actually achieved at the woofers' terminals, it is much less than the amps' specification due to speaker wire and speaker crossover. There will b... | |
| Cambridge 840a v2 equivalent Guess I should have read the article link thoroughly, as it looks like some A/V equipment has a "timbre match" feature. I find it very hard to believe it can make those JBL rears sound exactly like the B&W fronts, although it may improve, but ... | |
| Cambridge 840a v2 equivalent After reading this in your previous thread,My goals:2 channel (no subwoofer) listening at the same or higher quality than the current 8004-Cambridge chain. I should say that I am VERY HAPPY with my current 2-channel setup.Higher quality HT audio, ... | |
| Suggestions for New/Used amp under $3500 Soix is absolutely correct. Any amp will be limited in its performance by the signal feeding it from the Denon. An amp would provide more power that may improve the sound, but overall sound quality will be no better than the preamp output, regardl... | |
| Question about electrical outlets I doubt very seriously that two power strips into the same outlet will accomplish anything. Two dedicated lines from your service panel would work, but that would make sense for a bigger system, not just headphones. Look for something with "Digita... | |
| Dynaudio Focus 110.....Integrated amp???? I agree the MF A308 is a great amp, however the DF is 140, and not 1400. The amp just has plenty of muscle due to its power supply. Also, damping factor is just something you do not need to be concerned with. Read this thread,http://forum.audiogon... | |
| "Like" button for posts Or maybe a "Try Again" button, so we can make some sense out of what you are asking. | |
| Tannoy Speakers & Bi-wiring You'll find many different opinions on bi-wire, but I do believe it is best to do a true bi-wire, this is what Vandersteen recommends, which is 2 separate runs of identical cable. IMHO, I would agree with Stereo5 and use Audience Au24 jumpers to r... | |
| Recommendation for Integrated Amp w/ Big Sound I would also agree with Creek and MF, and add the MF A3.2, as it and the A3 and A300 were built in England, with the later ones built in Taiwan. | |
| NAD T973 vs NAD 275BEE You might give more information, as I am not understanding how you would be using a 7 channel amp vs two 275BEE's. | |
| How to replace tweeter on new Klipsch speaker Zd542 is correct, however it appears you only need to remove the trim piece around the tweeter unless it is connected to the other one, that part that has the Klipsch name on it. It looks like two separate trim pieces. You will probably need to ge... | |
| incredible inexpensive speaker That BMR is passiveJust out of curiosity, I had to check this out, and the BMR does has a voice coil, so therefore it is not passive. See the white paper,http://www.cambridgeaudio.com/media/bmr_white_paper-1372411331.pdf | |
| How to fix Yamaha DSP-A1 I doubt that there is anything wrong with the DSP-A1. When using main pre out, you must remove a pre out/main in jumper bar. This disconnects the pre amp from the internal main amp. These need to be installed for the main amp to work. So you have ... | |
| Power Cords: A Skeptic Looking to Dabble... Mceljo, then just get a power cord and see what happens. It may or may not make a difference. My point is that dedicated lines will definitely make a difference, and with dedicated lines, the power cord has a much greater probability to make a dif... |