rauliruegas
Responses from rauliruegas
| Resurrecting Shure V15VxMR Dear Autobot: No doubt that they are very good about, they re-tipped two-three of my carridges.I owned the V15VMR and I really don't like it as other MM cartridges I own. It is nice to know that huge Shure improvement, normally when I send to re-t... | |
| Arm Cartridge Matching Question? Dear Ray: You can find information here: http://www.cartridgedb.com/tools.aspNow, I own Grado cartridge and I mount on different tonearms ( One with an effective mass like your Zeta ) and runs very good, I don't think that you could have trouble a... | |
| Would Like To Hear From Strain Gauge Owners Dear Dave: Things are that I'm only try to understand why I heard what I heard on the SG ( different quality performance against a MC/MM cartridge ) and what other people report about. Dave, for me is not enough: it sounds good or I don't like it,... | |
| Audio Technica AT 666 is loosing air Dear Rugyboogie: Please check that on the outside rubber ring it is still all around ( outside the ruber ring ) a nylon thread, if it is good but if loose it then you have to replace because with out it does not works.Regards and enjoy the music.R... | |
| Setup of Ortofon SPU Royal GM II in Ikeda 407 Dera Dgad: I think that Dowunder is right, try it and I'm sure everything will be fine.Regards and enjoy the music.Raul. | |
| Would Like To Hear From Strain Gauge Owners Dear Intactaudio: I was talking about the MC/MM cartridges not the SG because at that time I do nt know that does not conforms with the RIAA standard.Regards and enjoy the music.Raul. | |
| Technics SP-10 Mk3 Power Supply / Control Unit I'm sorry I write this post at the same time that Lewm, fortunately we coincide about.Raul. | |
| Would Like To Hear From Strain Gauge Owners Dear Frogman: How is that?, are you telling me that a recording being played through two different equalization curves have no different quality performance?, I'm not talking or posted anything about " accurate frequeny response " I speak and post... | |
| Audio Technica AT 666 is loosing air Dear Rugyboogie: Agree, the Etbaby advise works too.Regards and enjoy the music.Raul. | |
| Technics SP-10 Mk3 Power Supply / Control Unit Dear Wireknot: Maybe this could sound something stupid but maybe ( I can't be sure ) the MK2 power supply could work with it and this mK2 is more easy to find, even you can buy a SP-10 MK2 ( very low price ) and take the PS but like I told you I c... | |
| Would Like To Hear From Strain Gauge Owners Dear Slowhand: Thank you for your kindness words, appreciate it.Regards and enjoy the music.Raul. | |
| Would Like To Hear From Strain Gauge Owners Dear Perrew: Answering your first question and IMHO when you play a recording that was recorded with ( before ) a non RIAA eq. standard then you heard a totally different performance of what is in the recording that comes with a different equaliza... | |
| Would Like To Hear From Strain Gauge Owners Dear Teres: Of course that when the cartridge signal pass through the phono stage what you want and the RIAA permit is a flat frquency response, but that's not exactly of what I'm refering to: sorry.++++ " The SG transducer (unlike traditional car... | |
| Would Like To Hear From Strain Gauge Owners Dear Flyingred: +++++ " I cannot understand why anyone would obsess about flat frequency response when ... " +++++I'm sorry but I'm talking about RIAA standar curve eq and how the SG device does not conform according it. What I'm tellng is not pre... | |
| Would Like To Hear From Strain Gauge Owners Dear Peterayer: here you can read about RIAA eq curve and you can observe on the diagram that the frequency range is: 20-20khz, I think that any one can confirm this RIAA information:http://en.wikipedia.org/wiki/RIAA_equalizationRegards and enjoy ... |