pindac
Responses from pindac
| Technics SP10 MK3 Restoration @dover I subscribe to the loop rigidity principle - platter, bearing & arm mount must be absolutely rigidly locked together in position to measure the groove accurately. Arm pods in my view are only as good as what they sit on, and often wi... | |
| Technics SP10 MK3 Restoration Thank You for the Tip about Warren.I have conversed with him privately and he has been quite supportive in offering his help. | |
| Suggestions for rca connector - diy interconnects Easy to Source, with a reasonable price for a Pure Copper Gold Plated Signal Pin. https://www.aliexpress.com/i/32795525594.html | |
| Technics SP10 MK3 Restoration I am at present instrumental in encouraging a Dr Kaneda based SP10 MkII Design to be produced using a Densified Wood to take on the role of the OEM Chassis.There are other options in the side lines to trial with the design once it is up and running | |
| Back To Static! In my mind and experience, the New Cleaning Method has proved to myself that my previous used cleaning method for LP's are not actually producing a LP that is clean. With this knowledge in mind, I do not feel the need to clean my entire collection... | |
| Technics SP 10 mc II. Worth looking at? I progressed through various motor drive TT's to DD and my impressive TT is the SP10 Mk II that is in use very regularly.I have no problems with other motor drives on TT's and make time to hear them perform. | |
| Back To Static! I use the Neil Antin Aqueous Cleaning Guidance.The Idea of Cleaning a vast collection is daunting using any cleaning method.The Bulk of my Vinyl has been cleaned on previous occasions and I am without any doubts that the New Manual Cleaning Method... | |
| Back To Static! I was under the impression their is a part used in producing a Home Smoke Detector that when removed and set up near the TT has an remarkable affect on elimination of Static Energy on a LP. I use the Yukimu ASB-1 Brush with COREBRID B fibres. I ha... | |
| DAC Shootout Starts This Weekend I do a lot of comparative listening and totally agree it is a worthwhile undertaking, if all goes well, there is a good possibility a Device will be discovered that is very pleasing to the individual doing the listening, and also one that interfac... | |
| Duelund conversion to DIY Helix Geometry Cabling The Link is to a Brand I have not discovered in past searches.That is the benefit of doing a search, the Robots throw other unknown products into the line up.This Brand also does Mini XLR but I could not make out the lead out pin materials.The one... | |
| Phono preamp tube rolling. Totally agree about a Cap' change having a profound effect.The Phonostage I am using has been auditioned in various circuits for the end design to be produced.When the prototype was almost complete and identified as being a very attractive perform... | |
| Phono preamp tube rolling. My 845 Mono's Input design is a little unusual as it has certain Tubes in Pairs that are only using Half of the Tube in the Circuit.There is only One 6SN7 Per Monoblock and these are only using Half of the Tube in the Circuit.It is always difficul... | |
| Phono preamp tube rolling. Absolutely Correct about the ECC33, hence the advice given to myself to discuss this Tube with the 845 Designer/Builder.It was Jaw on the Floor when the KenRad's were put into service. The KenRads and Sylvanias are both fine for ESL Speakers in m... | |
| Phono preamp tube rolling. The 6SN7 Tubes I have retained for use are Kenrad VT231 Black Glass and a Sylvania GT Tube.These are different in their presentation as an interface where they the input Tubes on 845 Monoblock Power Amp’s.I would very much like to try other Vintag... | |
| Duelund conversion to DIY Helix Geometry Cabling The Conductor Pins on these XLR Plugs as shown in the Links are in keeping with the Wire Choices being made within this thread.There is Plating as an option to have additional protection as referred to as the preferred choice. Not a Cheap Option o... |