jea48
Responses from jea48
| Do you demag or destat your CDs/DVDS? 07-12-14: JafreemanI spoke at length with my high-end retailer, here in MN, who swears by the Bedini Quad Clarifier. He states he never uploads a disc to his solid state drive or plays a CD that is not first placed in his Bedini. I trust this guy.... | |
| Do you demag or destat your CDs/DVDS? Jafreeman,Thanks for the acknowledgement. I was hoping you had not made up your mind from reading the posts of all the naysayers that had responded to your posted message.My Bedini Clarifier is the older dual beam unit. I have heard the quad is a ... | |
| Do you demag or destat your CDs/DVDS? What Czarivey and Mceljo are asking for is scientific proof that the minute magnetic fields produced either by the spinning disc or the paint on the top of the disc have any audible effect. 07-10-14: Timrhuscientific proof......What scientific pro... | |
| Do you demag or destat your CDs/DVDS? Sorry Jea, but there's no lab tested evidence at all.No information is quantisized or leveraged.Do you or any one here knows of published info with any magnitudes and/or quantities? Any info on flow of the lab test?Any scientific evidence will hel... | |
| Do you demag or destat your CDs/DVDS? "Pseudo science at best misapplying concepts in such a way that it sounds good to the consumer."07-10-14: MceljoMceljo,These guys have no dog in the fight. IAR International Audio/Video Reviewhttp://www.iar-80.com/http://www.iar-80.com/page53.html. | |
| Do you demag or destat your CDs/DVDS? I did a little quick research and it appears that CD players use photon lasers. Photons have no charge and therefore would not be effected by a magnetic field.Can someone explain what the mechanism is for magnetic ink to influence the playback of ... | |
| Do you demag or destat your CDs/DVDS? ,If your bike has aluminium frame, you can try to attract magnet there and see what happens. Try to attract CD with magnet and see what happens.07-09-14: CzariveyIs the aluminum frame 100% pure AL or maybe only 99% pure? What about that 1%?And ho... | |
| Ground Loop Video and advice. Solved! The "R" AUX RCA input jack on my C-2200 is bad. The short is inside the barrel somewhere. 06-12-14: 767400I would bet the C-2200 uses RCA jacks that terminate/solder to a circuit board on the back of the unit. Good chance the bad RCA jack ... | |
| Ground Loop Video and advice. A broken, open, signal ground return connection on an IC would be my first guess. Can you check the ends on the ics? | |
| Speaker hum problem - need help Jim (Jea-48) - just curious if you could say more about what/how to do the AM radio experiment. Should I actually tune into a station......or just set it to the very beginning or end of the band? What am I listening for if I set it to the station.... | |
| Whole House Surge Absorber. Kijanki,For the best possible protection the SPD (Surge Protection Device) should be installed in 2 spaces nearest the main breaker or in the case of a main lug only panel the SPD unit should be installed in 2 spaces nearest the panel feed wires t... | |
| Speaker hum problem - need help Mwsl,Do you have an AM/FM radio you could plug into the same mains power receptacle as the Coda amp? If so set the tuner to an AM station and listen for the hum/buzz.If the radio sounds ok then I would think the problem is not AC mains power relat... | |
| Buzz between Marantz SR5008 and Mcintosh C2300 Its a satellite cable btw. The ground is connected to the satellite chassis mounted on the roof. The other end is connected to gang box connected to the house ground.03-25-14: TccauxWell that does make a difference. For one the Jensen ground loop ... | |
| Directional speaker wires, what and why. if you really believe cables sound different depending on which way they are hooked up you are beyond help. geesus lol 03-22-14: DrusstheaxeDrusstheaxe,LOL, you really need to get out more often. . | |
| Buzz between Marantz SR5008 and Mcintosh C2300 Should have mentioned that. Interestingly, the coax is also going through the Furman. I disconnected the coax at the wall and the buzz did not go away. I by-passed the Furman direct to the SR5008 and buzz remained. I'd previously checked the cable... |