jea48
Responses from jea48
| Advice on RFI with a new integrated amp Marty, Is this your speaker cable?http://www.dnm.co.uk/cables.htmlhttp://www.stereotimes.com/cable022205.shtml | |
| Advice on RFI with a new integrated amp Not all ferrites are the same.Marty if you try ferrites on your speaker cables and or power cord make sure you install them as close as possible at the entry point of the amp. | |
| Advice on RFI with a new integrated amp Hi Al,You are probably right but if Marty has some ferrite beads it won't cost him anything to try them on the speaker cables and or the power cord. Maybe the radio tower transmitting antenna is close to where Marty lives..... Or maybe it is a hi-... | |
| Advice on RFI with a new integrated amp Marty,You might try some clamp-on ferrite beads on the power cord of the amp and on the speaker cables. You never answered how long the speaker cables are....RFI Tips And TricksQuote from Link:AUDIO AMPLIFIERSIt's quite likely that the audio ampli... | |
| Advice on RFI with a new integrated amp So the shorting caps didn't address the RFI, even when in the phono stage. Would the next step be swapping out the moving coil stage and putting back in the other piece (I am not sure what its is called -- I think internal jumper? If so, who can d... | |
| Cap voltage Why 600v when the pre only puts out about 2v. Don't smaller voltages sound better? Lewhite 2 Vac signal... What is the DC power supply voltage applied to the plate of the output tubes? The caps block the DC voltage from the power amp's inputs. | |
| Advice on RFI with a new integrated amp I am currently consideringshorting terminators on the phono, and other output pots and found some terminators online (audiophilia article).Do not install shorting plugs on the outputs. Ok on the inputs.... At first I thought it might be my changin... | |
| How to connect Phono Stage from vintage receiver Almonduck, Something else you may want to try,... reversing the non polarized plug of the marantz 180 degrees in the electrical receptacle outlet. One direction should be quieter than the other. Noise, hum and AC polarity. | |
| How to connect Phono Stage from vintage receiver TT >>> to Marantz phono input >>> Tape out of Marantz >>> to line in input of integrated amp.Marantz receiver input selector set to phono for tape out.Make sure volume control on receiver is turned all the way down to pr... | |
| This makes no sense, but yet.... That is silly. Directionality of a cable is determined from a few purposely defined characteristics. I hate to say this and sound rude...but the quality control must be lacking if you experience an obvious difference. There is absolutely NO reason... | |
| This makes no sense, but yet.... You may already know this but just in case, the arrow on the Nordost cable points to the source, not the direction of flow like every other cable.11-06-09: RhljazzRhljazz, I believe at one point Nordost changed their mind..... Early cables arrow t... | |
| This makes no sense, but yet.... I had the sprung cables between my CDP and amp and they were unbearibly bright -Try flipping them end for end and listen to them again. | |
| Will I benefit with 20 or 15 amp dedicated lines A subpanel can have its own grounding, isolated from the ground of the main panel. I used 6 gauge for the ground, bolted to the center of a buried 2'x2' steel plate as is done for swimming pool installations.10-28-09: EssentialaudioNot in the USA.... | |
| Will I benefit with 20 or 15 amp dedicated lines I can't understand why you need a 20 amp when your gear only uses about 500 watts. 1 amp= 110 watts so a 15 amp circuit is about 1700 watts; a 20 amp is about 2200 watts, it is like using a 5 amp fuse when you need a 1 amp fuse. You are better off... | |
| Will I benefit with 20 or 15 amp dedicated lines Kitegod,The biggest expense of the job will be for the labor of the electrician. Install 20 amp branch circuits. #12 awg NM-B cable minimum.....Make sure the new branch circuits are installed on breakers that are fed from the same Line, leg, in th... |