golfnutz
Responses from golfnutz
| Question for those who use REL subs with Wilson speakers Sorry, can't offer any opinion, just a couple of comments.Do you use corner bass traps? If not, you might get more effectiveness with them.Have you tried stacking the 2 subs that you already have to get a sense of what it might sound like having t... | |
| Need insight on these amps @three_easy_payments So your assessment of the OP's "problem" and advice to the OP is based solely on your referencing someone else's review? None of this is based on your first-hand experience? And your advice is simply "sell everything and buy... | |
| Need insight on these amps @audiogabby , sorry I doubt an amplifier is going to fix your problem with those speakers (based on Stereophile review, good bass, but too polite in other areas). You should consider selling the speakers as well, and purchase an amp and speaker co... | |
| How do you owners of the Pass Labs int 250 like them? Thank you @audiosgp1, appreciate the feedback.Congrats on the INT-250 as well. | |
| DAW vs Alexia 1 vs Sasha 2, descending order of $$ There’s a used Gryphon Diablo for <$12k listed on the internets. Might be worth searching the net for opinions...I don't think XA60.8 will be enough to do proper justice for any of those speakers. | |
| How do you owners of the Pass Labs int 250 like them? @audiosgp, what was it that you didn't like about the Diablo 300?On paper, and based on online reviews, I would easily pick the Diablo. | |
| Time to buy a class D amp? Sorry @hm1 (Howard Milstein) but not a single negative comments in any of your reviews that I read. They all appear to be written as advertisements. Here's a good example of what I mean (W4S mINT review): Out of curiosity, I decided to laboriousl... | |
| What Class D amps will drive a 2 ohm load @nitrobob - it would appear that V series amp is based on the IcePower 1200AS1/2 modules (not sure if it’s the 1, 2, or combination of both), which has a minimum impedance of 2.7 ohms. They also mention you should use a 20amp circuit for best resu... | |
| What Class D amps will drive a 2 ohm load OK, so what is the definition of instability for these Class-D amplifiers? Since they have over current protection mode, and soft clipping capabilities the amp continues to operate, but not optimally. Without the use of an LED display to the circu... | |
| What Class D amps will drive a 2 ohm load Rather than saying from an earlier post, I'll just paste it in again (from the spec sheet):Overload Protection - In case of high-amplitude continuous low frequency signals in loads lower than 4 ohms the power supply may not be able to deliver the ... | |
| Help me select an integrated amp for Thiel CS3.6 speakers I have my doubts about the Hint 6 being able to drive the CS3.6 speakers properly in a 25' x 25' room. It's only rated at 160 and 270 watts into 8 and 4 ohms. The Hint is basically the same as the Halo Integrated.From Sterophile's Halo review: "F... | |
| Help me select an integrated amp for Thiel CS3.6 speakers Honestly EPZ, you should consider selling those speakers (assuming you’ve purchased them already). The real issue here is the size of your room (25’ x 25’ speakers in the corners only). As others have mentioned, you need a high current amp to get ... | |
| Watt Puppy 7 needs new or used Amp and Pre-amp Tweak Audio EVS 1200 is based on ICEPower 1200AS1/2 Class-D modules. I had these modules running a pair of Watt/Puppy speakers and they just couldn’t handle the impedance for these Wilson speakers properly. The amps never failed, but the results w... | |
| What Class D amps will drive a 2 ohm load It had trouble with Thiel CS3.6's and was a joke with the CS5's.So the Icepower 1000ASP had trouble with Thiel CS3.6. Well, they are a tough load through most of the frequency range.The 1000ASP should have an easier time with the Thiel CS3.6 than ... | |
| What Class D amps will drive a 2 ohm load Yep, WFS SX-1000 uses those same modules.Spec sheet specifies 2.0 ohm minimum load, as well as 40 amp current (peak). Unlike the Icepower 1200AS1/2 being rated at 2.7 ohms.Also included in the specs:Overload Protection - In case of high-amplitude ... |