diwakarv
Responses from diwakarv
| Sub w/a CJ ET3 SE I am not sure about best way but I was using splitter at the o/p of ET3SE going to my SB13 ultra. There was no detectable loss in audio quality from speakers. | |
| which CJ amp to go with ET5 ? No, I have not demo CT6. | |
| Anyone have honest opinion of Jolida amps? I have compared Jolida 502P and 801BRC with Conrad Johnson ( classic sixty and ET3SE) over hours and hours. I can tell you the difference is not all that much. Jolida had KT88. In my opinion , it is excellent value for money. | |
| which CJ amp to go with ET5 ? They are all on dedicated circuit. | |
| which CJ amp to go with ET5 ? Power Chord are Shunyata Copperhead , Carden Golden Reference. I am using Cardas neutral Reference for IC. | |
| Suggestion for new panel/dedicated line Thanks Zephyr24069 for response.My electrician was giving me about same quote for two/four circuits. I am currently using three, one for DAC/pre amp , other for AMP and last for subwoofer. Fourth is unused right now ( future proofing :-)I ordered ... | |
| Suggestion for new panel/dedicated line Thanks Zephyr24069, Do I actually need four EP 2750 for four dedicated circuits ?I will be using one circuit for DAC/Preamp ( Duplex outlet), other circuit for amp. It will be one circuit dedicated for subwoofer and one of later expansion ( may be... | |
| Suggestion for new panel/dedicated line Phase I of upgrade is complete. My electrical panel is now upgraded to 200A CH type from Zinsco 100A. My stereo's mid range is opened up quite a bit. Instrument separation is improved.Phase II would be done tomorrow ( 4 dedicated circuits). Two of... | |
| Electrical panel : Ground/Neutral bus bar question This is response that I got from eatonMy question Hi,Can I replace neutral/Ground (Tin plated aluminum) in CMBE4242B200BTS panel with ILSCO copper bars ?ThanksReply from EatonSince its a service entrance panel, the neutral/ground is bonded, so I ... | |
| Electrical panel : Ground/Neutral bus bar question In my opinion ( as an circuit engineer), if the resistance is introduced in source path ( breaker contact, OR main distribution bus) or return path ( to GND via Ground/Neutral AL bus), it is bad. It is definitely worse in return path since all the... | |
| Electrical panel : Ground/Neutral bus bar question Here is picture of the panel that I discussing abouthttps://www.flickr.com/photos/131393447@N08/17442124326/in/shares-S47X7U/ | |
| Electrical panel : Ground/Neutral bus bar question Thanks Cdrc. I am using copper SE cable & 4 AWG solid copper GND wire terminated to 8 feet solid copper bar ( about 50 feet from Main panel) and to water mains. I have bought Cardas in wall AC for two dedicated circuit, 10/2 romex for subwoofe... | |
| Electrical panel : Ground/Neutral bus bar question Hi Jim,It is always educational to read your response. I takes me an hour to read/understand your post and additional couple of hours to reply :-) I surely appreciate your feedback.CH panel CMBE4242B200BTS uses part no. N-8108-86 , catalog no. NBA... | |
| Any Conrad Johnson HD3 USB DAC user I am owner of CJ HD3 for about eight months now and I like it very much to my taste. It sounds very analog ish with details. I have not compared it high end DAC though. | |
| Electrical panel : Ground/Neutral bus bar question May be, it wasn't clear but I am trying to replace Aluminum Ground/Neutral bar with Copper and I am finding hard to match mounting holes etc. My question is, can I buy ILSCO N174 ( or alike) and drill hole ( at wire hole) to match with mounting po... |