dasign
Responses from dasign
| HDMI VS Analog cables for SACD Oicu812I totally agree with you on bluray player for music, they are not the greatest. I mainly use it for concert movies. I use a Sonore UltraRendu/Benchmark DAC 3HGC playing streams from Roon/Tidal combo. | |
| Benchmark DAC 3 HGC or RME ADI-2 DAC Yzzsantabarbara, I currently own the Benchmark DAC3 HGC and had same issue with the volume control adjustment. I had to open the DAC and move the XLR output pads to the 20 db position so to have a proper volume range adjustment. The factory standa... | |
| I want to find these specific knobs I would bite the bullet and give Croft a call. I’m pretty sure that these are custom knobs and will be next to impossible to purchase outside Croft. You could also contact a Croft retailler/distributor to see if they could be of any help. | |
| Modifying Philharmonic 3 crossovers Ask your electronic parts vendor to measure either the 18 or 22 uF caps closest to your 20 uF you are looking to replace. Capacitors can have a 10% value tolerance and I am pretty sure that you will be in position to find the requested value. I kn... | |
| HELP! Need Operation Manual on Yamaha CT-810 tuner Thank you Yogiboy, I already found that info but really would like to have the original manual in PDF. | |
| The Monk: Live at Bimhuis Acman3, I will check this out.Thanks. | |
| Moving from 120 VAC to 220 VAC operation on Krell monoblocks I have configured the Krell amps for 240 VAC operation but unfortunately the left monoblock amp did not have its stanby LED lit upon initial powering, while the right amp was behaving correctly. Krell amps have a breaker in the back to power the ... | |
| Moving from 120 VAC to 220 VAC operation on Krell monoblocks Just finished installing the 10 gauge dedicated circuits. This wire is a bear to work with. I used a core solid copper NMWU 10/2 (black sheeted cable). This cable is so stiff that it was trying to get out of the Furutech GTX-D (R) wire clamping sy... | |
| Moving from 120 VAC to 220 VAC operation on Krell monoblocks Contacted Krell again and the setting for 240 VAC is 222. Thank you msalvatore for pointing out your settings. These seems to be specific settings for 220 VAC and 240 VAC. I initially asked the wrong voltage setting to Krell (220VAC). Special than... | |
| Moving from 120 VAC to 220 VAC operation on Krell monoblocks Thank msalvatore for your input. Did you run your amps on 120 VAC/60 Hz initially? What were the improvements moving from 120 VAC to 240 VAC? Also you indicate that your switch configuration was 222. On which model of Krell amps?I have contacted K... | |
| Shunyata Anaconda CX power cord - Ok to use on 240 VAC? Bar81,Thank you for your reply. This is what I thought.*************************************************************Williewonka,I totally understand your concerns about local electrical code. Do not worry, I have done my homeworks. The 10 gauge wi... | |
| Moving from 120 VAC to 220 VAC operation on Krell monoblocks Hi Chris,You're my favorite philisopher :-)*****************The Canadiens are in hockey hell rigth now...Daniel | |
| Moving from 120 VAC to 220 VAC operation on Krell monoblocks Thank you ct0517 for your caution advice...I'm a certified electronic technician and got shocked by a few Kilovolts when trying to repair a tube-based spectrum analyser a few years ago. My wedding ring was too close to the high-voltage wire feedin... | |
| Moving from 120 VAC to 220 VAC operation on Krell monoblocks Hi Elizabeth,I’m all in with your comments and this is why I’m doing this. According to the MBL article, using 10 gauge wire is the first step to audio heaven and moving to 220 VAC is the second step.This is going to be a nice experience and looki... | |
| Moving from 120 VAC to 220 VAC operation on Krell monoblocks Started looking into Siemens 240 VAC/20 A circuit breakers. I may just go direct doing the 240 VAC mod, since the core of the work is rewiring the dedicated circuits to 10 gauge wire.Daniel |