alexberger
Responses from alexberger
| 300b lovers Here is an example of direct coupling: http://www.single-ended.com/Lagarto/shishido/811A.png Is 6f6 grid load easy enough for SRPP? ECC82 can be changed for 6sn7. What do you think about this schematic? | |
| 300b lovers Hi @donsachs , I have two questions about your new amplifier: 1. When you decided to go to an interstage transformer after the input stage, why did you stay with 6sn7 and didn't move to something like 5687? With 5687 you can get even wider band... | |
| Resolving CD Transports Crowd Sourcing It is interesting how is a new Schiit Urd compared to Jay Audio, Teac VRDS 701T and Project RS2T transports. | |
| 300b lovers Hi @lynn_olson , According to your comparison between RC coupling and IT coupling, IT coupling between input and driver stage should increase slew rate (dynamics, trancients, speed) similar as it does between driver and output stage. Isn't it? On... | |
| ALTEC MAGNIFICENTS.....MODIFICATIONS I have Altec 604E since 2005. Two year ago, I built crossovers based on original n1500 schematics using good quality modern parts. The difference in sound is huge. It is like different, much more expensive speakers. The chokes in the original cr... | |
| 300b lovers Hi @donsachs , Will you present your new amplifier in the Montreal Audio Show in March? | |
| 300b lovers Hi @donsachs, Lynn told in this thread that you prefer schottky diode in your amplifiers. Why do you prefer schottky over other diodes? Hi @lynn_olson , As DIY I can adjust my amplifier to my own taste preference. But compared to experience... | |
| 300b lovers Hi Lynn, In my SET amplifier is IT coupling between driver and 300b and RC between an input and a driver stages. I think I understand why the tone issue appeared. I played with driver tube B+ voltage and current. The cathode resistors 680 ... | |
| 300b lovers Following Lynn and Don recommendations, I added a separate filament transformer for 300B. It made the sound clearer. Then I added a separate transformer and rectifier for driver and input tubes. I use a Hexfred bridge (Ralph's recommendation) and ... | |
| Loudspeaker sensitivity and dynamics: are the two inexorably linked? Another factor is - the crossover parts like resistors, inductors are heating when you push dozens of watts on a speaker. As a result, parameters of drivers and crossover parts are changing with the power. As a result most low sensitivity speakers... | |
| Loudspeaker sensitivity and dynamics: are the two inexorably linked? Just imagine speaker voice coil even with most effective dissipate heat is possible. When you need dozens of watts to drive the speaker the heat on this voice coil is huge. You can’t cool it in closed small box without fan. Another story if it is ... | |
| 300b lovers The question is about of calculating C-Miller for a pentode tube in triode mode. If we have no data of C input at triode mode, or also no data of Cg1-g2, then how do we calculate C-Miller? How is big the total input capacity in 6V6 in triode mode ... | |
| 300b lovers Here is Eleckt schematics: http://4tubes.com/2-SCHEMATICS/BY-BRAND/ELEKIT/TU-8600/TU-8600R-Amplifier-300B-Schematic.jpg Global negative feedback, parallel 12au7 driver, 12ax7 input, semiconductor bias control and power supply stabilizers. chrom... | |
| 300b lovers Hi @atmasphere , I will use this rectifier for the driver and the input stages. So i don't need a very high current and power capability. | |
| 300b lovers Hi @donsachs , I have a question. I bought and received a power transformer for the driver tube's power supply. This transformer has a central tap for the rectifier. I also bought 4 schottky diodes. What type of rectifier will sound better: a cen... |