need help with choosing right cables


my system sounds bright.im sure cables are the problem.im using monster 950i innerconnesct and monster biwire speakercables.looking for more of liquid sound with out breaking the bank. my set up: b&k725amp denon333avr msb linkdac3 feeding pioneer333 as transport with monitor audio silver5s speakers.thanks to those who respond.trip
trip
Trip, if you feel the need to rebuild your system, or even to analyze it, here are some hard learned tips I've come to embrace after many years:

1. Start with your speaker choice. Typically, your speaker selection will more strongly dictate the characteristics of the range of upstream electronics than any other component choice. Some speakers are fairly forgiving and get along with just about anything, while others do not. For example, I'm partial to Thiels, and this forces me to keep a close eye on high current delivery and relative warmth from everything upstream. Like Avantegardes? Then the spectrum of flea powered SET amps is available. The key word should always be synergy - look to balance the relative strengths and weaknesses of your components against your listening preferences. BTW, I think the B&K is ok with your Silver 5s.

2. Once you have found a speaker/power amp combination that works for you, then look more closely at the front end. While it can be critical, if you're budgetarily strapped, I would rather cut corners on the pre-amp stage as opposed to the front end. An integrated amp is sometimes a good alternative under these circumstances - and there are some very good ones today. Better front end gear with their better output stages can sometimes get by with a cheaper (and sometimes better) passive pre.

3. Next look to cabling to fine-tune any residual shortcomings, starting with your speaker cables, then interconnects from your front end forward. While I've found it's OK to mix speaker and IC makes, it can become quite an art to intermix IC brands in the same system. Cables can be quite vexing, and places like the Cable Co can be very helpful here. Cables will not fix a fundamental mismatch elsewhere, but they can screw up an otherwise fine system if poorly selected. Look to cabling to compliment, not correct your system, and you're on the right track.

4. Don't overlook your power supply. Start with a simple 20 amp dedicated circuit, then look to good conditioning for the front end and upgraded power cords throughout, starting at the amp and front ends. If you need power from your amp, I've found that superior dynamics result from going straight into a dedicated circuit outlet.

5. Tweaks, such as vibration control and room treatments may come next. These can bring some noticable improvements, but unless severe (hard floors and glass everywhere) I wouldn't turn to them until more fundamental electronic issues are resolved.

When making changes, give your system at least a week to settle in (longer if new components are involved) before making any further changes.

I'm a big fan of having a vacuum tube somewhere in circuit, especially with digital, to add smoothness and warmth. You can also roll tube types to further fine tune the sound. Looking at your situation and budget, if you want more warmth and like your speakers, I'd ditch the Denon, MSB, Pioneer combo and go for a warmer, tubed output, one-box CDP and a passive attenuator pre. After that, I'd turn to your cables, depending on where you need to go from there.

Alternatively, you can do as Sean has suggested, and experiment with just cables - but depending on just how bright your system is to you, I think this amounts to band aid audio under the circumstances.

Again, these are just my opinions on how to do high-end, and others may have a different view.

Good luck to you, and remember that this is all supposed to be fun.
Source first .the best speaker in the world cant make a bad source sound good.A good source can make an average speaker sound better.
Garbage in Garbage out.
Leafs, I used to believe that theory, particularly as to phono cartridges. But I now think that every link is equally important. However, I think that a poor speaker match is much harder to remedy than one involving the front end. Beyond a certain price point, I've found the performance differences among front end components much less profound than those among speakers at the same price point. And past a certain price point (which I would hope we are talking about here), most front end components are competent enough to not output garbage, but perhaps vary in reduced resolution or other miscues of omission. This is a much different situation from a $5000 speaker which leans warm or bright and requires a 400 wpc or a 10 wpc 300B amp to reach balance. The power amp in particular has a much more intimate sonic and electronic relationship with the speakers than it does with a DAC or phono stage. Witness the audiophile who forces his Transcendent 25 watt OTL upon his new Thiel 7.2s - a singularly unnatural marriage. Obviously, I do not advocate the purchase of junk front ends, and I never said as much. But speakers at every price point present a much wider spectrum of sonic and electronc variance, IMHO. Because of this, I've come to the conclusion that you start with the speaker, which fixes the range of usable associated electronics. By all means you should mate it to a quality, perhaps equally priced, front end from there
My advice was pretty bad. What you might do before you change any components, like another poster said, play with speaker positioning. Maybe try a pair of the acoustic imager foam rings to reduce diffraction if they fit on your speakers baffle, a $5 tweak. Depending on your room some profoam level one by RPG would smooth out some reflected energy for another $50 and, depending on the cabinets, if they resonate a bit, try some dynamat like material for another $20. I did the latter on a pair of klipsch epic series and while it never tamed my harshness, it did have the effect of adding a subwoofer, the bass tightened up and went deeper, it was neat. All three of those tweaks are far cheaper than any electronics upgrade and, IMHO, better than buying any cable. None of that will "break the bank" as you said. Maybe even get the monster out and try a little run of Kimber Kable 4PR, its cheap, or even try just straight 16g wire and stock interconnects and see how things sound. I'm not a fan of monster. And put the speaker grills on, that can help too. All those tweaks will run you around a hundred+ bucks.