Mono Cartridge Question


You chaps have watched me struggle with the issue of my London Decca Reference being irreplaceable, and then joyfully learning that John Wright has a successor after all. You have seen me buy and test three other MI designs (Nagaoka MP-500, Grado Statement3, Soundsmith Sussurro MkII) along with my older MC cartridges (Ortofon Kontrapunkt C and Benz Micro Ruby 3). Since those struggles have led me to owning two SME turntables and four tonearms, I am now torturing myself with the question of whether one of those four should be home to a dedicated mono cartridge. Remember, I only have one ear and cannot hear stereo at the best of times. A mono cartridge for my few dozen mono recordings would be a matter of reduced surface noise and possibly some improvement in dynamics.

I can get hold of an Ortofon Cadenza Mono (two voice coils so not true mono) for about 1600CDN, and a Miyajima Zero for 3450CDN. So the question is this: am I mad to even think about it? Money is not what it once was before I retired. There is no opportunity to go and hear these before purchase, without spending much more than purchase price on travel.

Shall I "make do" with my rather good stereo carts for my mono LPs or is there something better waiting for me when I get out those Parlophone Beatles LPs?

 

dogberry

@goofyfoot, it is definitely the opposite from what you were told. A larger object will not fit as far down into a 90 degree groove versus a smaller object of the same basic profile.

The degree to which they differ in their elevation on that groove wall can also be easily calculated. A 1mil (25.4 micron) diameter conical will ride about half way down a nominally cut unmodulated groove (50 micron width). A 0.6 mil (15.2 micron) conical will ride about 20% lower. That isn’t small change.

The contact area of both sizes are VERY similar. Why? Because the point of groove wall contact is on the spherical portion of the stylus. (Technically speaking, points of contact with a sphere are infinitely small but in practice you must consider groove deflection.)

Using a spheroid contact area is VERY important to allow for tolerance errors on the mounting of the stylus to the cantilever on the azimuth axis. This is also why fine line styli have a major radius. This is also why proper azimuth alignment has NOTHING to do with the stylus alignment in the groove regardless of stylus profile (up to a point, any way, but that point is usually past 2.5 degrees level headshell and often more)

Now, I would certainly argue that the smaller contact surface area of the stylus to the groove wall, the greater the chance for groove damage because the force is distributed over a smaller area, causing greater groove deformation. This is another advantage of fine line contact styli over conicals and also why a larger conical probably has a slight edge over smaller conicals in avoiding groove damage which is quite the opposite from what you’ve heard.

However, I AM ALWAYS OPEN TO NEW, YET CONFLICTING, INFORMATION. I invite it as it is the only way I’ve been able to help push this industry forward so far.

@wallytools Of course not all grooves are the same size. Just after shellac 33 1/3, the vinyl groove was at it’s widest, then came the microgroove and now we grooves equal to the size of a stereo record. So I’m not sure which of these grooves you’re talking about but I’m assuming you're referring to the microgroove. If someone is using a 1.0 ml stylus on the early mono records, it is reaching very far down into the groove but slightly less in the microgroove. Most likely only a 0.7 ml stylus should be used for later records and recent remasters. Pretty much any cartridge designer will tell you not to play newer records with a 1.0 ml stylus. So I’m curious,what are the variables between the different stylus and the different groove sizes?

When I found the DaVa to be the most high resolution cartridge I heard, I was initially worried how 3.5g tracking force and conical styli would affect valuable, high priced original records. Also, I am mainly a fan of linear tracking using Vyger especially with Top Wing Red Sparrow, which tracks below 2g, especially as I was introduced to it by an LP collector who had tens of thousands of LPs, some priced well over 10k. I also think that the issues pivot owners face because of the offset angle, aligning the cart right, and getting anti skating right, coupled with varying cartridge samples, can lead to incorrect set up causing harm to the vinyl. This is fine as most people are using reissues, or inexpensive vinyl, and it can be replaced easily, but expensive originals cannot.

As a background, my other favorite cartridges are VDH stradivarius and the Lyra Atlas Lambda. Also, Zyx, Allaerts, airtight, MSL, GFS, Decca, are all nice, and at lower prices, SPU is musical with less details and some rolloff, and Hana and Audio technica are good value for money. But as with Denon 103, you can hear less details.

Therefore when I liked Dava, conical and 3.5g tracking was initially a concern for me, but the sonics were so good, and there was so much more musical information, I decided to check with owners who use good LPs, and repeated play on their favorite ones using DaVa did not wear out the LPs. To start with, if you use fine style to track at 4g, you will cause harm, but with conical styli the pressure is spread over a greater area. What Darius then explained to me, is that most conical styli are 0.6 mil tip or more, he keeps it at 0.5 as per Shure documentation, which he found to get past that issue.

Regarding detail and resolution, he said if he used his conical styli in similar ways to how others use finer styli, it will be less detailed. But his cartridge is designed to kill eddy currents, which mask details, and the lack of eddy currents is what increases the detail. The higher detail and resolution via DaVa against any cartridge should be easy to hear, whether on rock, jazz, or classical. If you want more technical details of how the eddy currents are suppressed you will need to check with Darius. So I decided not to generalize with other conical styli, DaVa for me is onto something and they are changing things.

 

My further DaVa experience here. Please note one point there, I like TD 124 but normally find it has less resolution that higher level tables. However, on the TD 124 with basic DaVa vs Continuum Caliburn with Etsuro Gold, I found the 124 to have higher resolution. The owner also sold his continuum after that, and now bought a restored commonwealth to play the DaVa. This owner also has a Vyger with Red Sparrow.

After I receive my Dava, I will do a compare of it with Audionote field coil (another owner who had AN field coil put in sale after listening to the DaVa), and with Top Wing Red Sparrow on a Vyger on another system (not same as one above but a Cessaro Zeta), but this will take time. 

 

To clarify, my DaVa comment was on stereo and not mono. I haven't heard the mono. 

Look into the Miyajima Infinity mono cartridge. One of, if not THE, best true mono cartridges.