2. analog
  3. 168226-3976

Classic Ortofon Cartridges: The MC2000 MK II or the MC3000 MK II?

So I have owned quite a few Otofon cartridges over the years, everything from the modest OM cartridges to a couple of Cadenza up to an A90. I typically enjoy Ortofon cartridges.

Now one I have never owned is the MC2000. It seems from a bit of reading I have done that owners of the MC2000 felt it was the most accurate of the Ortofon cartridges, and that releases after it were not its equal.

However, when you look at the MC3000 it has a higher output level that would allow it to work with my Esoteric phono stage. The Esoteric is happy running an MC200 on it which has .09 mV output. but the MC2000 is .05 mV. The MC 3000 MK II is .13 mV from what I find.

Has anyone spent time listening to these classic MC 000 series of Ortofon cartridges? I know there is also a 5000 and 7500, but those seem to be pretty rare.

Regarding the MC2000, I wonder if I use a low mass headshell if I can use it on the Dynavector DV505. I don’t think the mass of the arm in the horizontal plane should affect it, and the vestigial arm can be configured to be an appropriate match for the compliance on this cartridge.

I currently have an MC200u on the arm and its very surprising regarding how good it sounds. Its actually pretty neutral, pretty expressive, but just a bit relaxed in the top end. I certainly enjoy it, but I wonder how these statement cartridges from the classic Ortofon line will sound. These would have been from their long time designer who has now retired, so its a different era of Ortofon versus what their current offerings are. Even though we should acknowledge that the current cartridges use design principals that were developed from this earlier time period and engineering team. 

Thoughts?
neonknight
edgewear
543 posts
 
Dear lewm, the MC7500 has a tendency to sound a little edgy or bright in the wrong set up. I think this has mostly to do with that Ortoline stylus profile. So spot on azimuth and SRA are crucial, but I assume you have that covered.

It took some time to find it, but the LH 7500 headshell made a very positive contribution and so did the LW-1000S leadwires. You would  think 7N copper would be the best match to the 8N copper coils (8N copper lead wires are not offered by Ortofon or anyone else I think), but these silver wires contribute to a neutral balance comparable to MC2000.

It sounds very good in FR64S (all my cartridges do, even the high compliance MC2000), but even better in Audiocraft AC-4400. And perhaps contrary to what one might expect, it likes the phono amp (at 500 ohm loading) better than the Ortofon T3000, which is basically the same as the dedicated T7500. Hope that helps.

Ag insider logo xs@2x
rauliruegas
12,832 posts
 
Dear @neonknight  : I owned 3 MC2000 and owned/own/listened almost any Ortofon cartridge in my system, so certainly I like Ortofon designs.

""  It has to have the OEM cantilever. ""

Not really, it was not that aluminum cantilever what makes the real difference but the cartridge engine and suspension design . The MC2000 has an over 30cu on compliance and yes it's a really great cartridge tracker and along what I pointed out from this tracking abilities comes part of that very high quality performance.

In one of my samples I bended the cantilever  and time latter I decided to send to VdH to fix it.
I received it with boron cantilever and VdH stylus tip and as good as the original was/is the boron/Vdh  performs with better quality performance level with out loosing the original cartridge attributes.

So, you can buy it in almost whatever condition  ( about cantilever/stylus ) and you can send to Northwest or Expert stylus or Vdh to fix it.

My boron/Vdh was unique and probably the only one out there, I sold it. I'm not a collector but I owned and own a lot of cartridge just to know its " signature " quality level and obviously to enjoy MUSIC.

So, don't worry about that " original " word at least with the 2000.

 Now, the MK2 is a way different cartridge and there is no comparison but the 3000MK2 is something to listen and yes different than the MC2000 but not to different.

In the other side you can look for a second hand A90/A95 and you are " there " too with out be disturbing your self for that very low MC2000 output, its high weigth and very high compliance because you have to fix all these cartridge characteristics for the 2000 can shows it.

Regards and enjoy the MUSIC NOT DISTORTIONS,
R.
ihcho's avatar
ihcho
609 posts
 
How are MCx000s compared to other LoMC Ortofon cartridges, like MC20, SL15, SL20? I've used them with MCA-76, T-20 and T-30, and they all sound fantastic, but never had a chance to use MCx000s.
I used MC100 briefly, but it was not as good as others.
 
pindac's avatar
pindac
2,452 posts
 
If a Cantilever has been treated in a manner where it has damaged the Bobbin, with the earlier designs of Ortofon Cartridges, there is going to be a long search to get the support to repair the damage.
Even Ortofon will not guarantee the original parts are used, an updated compatible part might be substituted, and might not be to the Spec of the original design.

A Cartridge purchased with a Damaged Stylus will be a Wild Punt, as the Internal Damages will be a unknown.
A Inspection from a Third Party Rebuild Service might result in a rejection of the build as the Donor Cartridge is not suitable.

Many of Ortofons Internal Assemblies are in house designs, that are unique to their Brand and not items selected from a supply chain, as some other recommended Cartridges.
Ortofon does not share these assemblies freely.  

Again Caveat Emptor is the best guideline for such a purchase 
neonknight OP
341 posts
 
@rauliruegas 

I have owned an A90 and a Winfeld, and enjoyed both cartridges. I am not as wild about the A90 as other cartridges, although it is a fine moving coil. The top end isn't as vibrant as I prefer, although it's remarkably free of colorations. 

I might give a MC3000 II a go for the interim, and keep my eyes open for a nice MC2000 or perhaps a 7500. 

To be honest I like my Ikeda 9 Kawami, but  one day it's going to need a restoration. When that time comes it would be nice to have a quality stand in for it. 

My other favorite is the Transfiguration cartridges, and I imagine one would sound nice on the Dynavector. I would also be interested to try the Audio Tekne. 
More to discover