Concerned about my cart/pre pairing


Long story short..

I started with a Dyna DV20x2HIGH and a Dynaco PAS3x, then upgraded the pre to a Rogue RP-1. One day was cleaning my table and #%&%! up the needle, so I just coughed up the money for a new DV20x2LOW now that I had the Rogue's choice of higher gain setting for MC carts (58db). Purchased from a reputable local dealer. In reality when making the purchase I didn't know too much about how cart specs/phono stage gain, etc works (I'm just starting this HiFi journey), just went with what was suggested. Now, I notice that I really have to crank the preamp volume sometimes when listening to records and the output is definitely less than it was before. It still sounds good, but on the occasion I do crank the volume to near max (50-60 out of 60) I hear some noise in the upper ranges, maybe a little hiss. After doing some research about the subject I'm concerned that the 58db gain on the RP-1 might be too low for the 3mv rating on the cart, and I'm missing out on the best performance of the Dyna cart. Obviously when switching to my Bluesound NODE the volume output is WAY higher. 

So....at the end of the day I still enjoy the sound, but feel concerned about having to have the volume  so high, and wonder if I'm missing other things like detail, dynamics etc....or am I over thinking this?? Do I really have to invest in a new phono pre in the future? Was this not a good match?

Thanks in advance!
128x128jin78
Despite the many self-assured responses you received, no one can really analyze the phono gain inherent in your system without also knowing something about your amplifier and speakers.  First, the SPLs coming from your system depend not only upon the output from your preamp but also on the input sensitivity of your amplifier.  Input sensitivity is defined as the signal voltage required to drive your amp to its full output.  Typically that is anywhere from 0.5V to 2.0V, somewhere in there.  After that, we need to know the efficiency of your speakers and the size of your listening room.
But we can say that a cartridge that puts out 0.3mV into a phono stage with 58db of gain will result in a signal voltage of around 0.24V at the output of the phono section.  Bear in mind that the figure of 0.3mV is published by the manufacturer for a stylus velocity of either 3.54 or 5.0 cm/sec. Most music will actually push the stylus around a bit faster than the standard velocity; thus usually the rated output is a bit pessimistic as far as the actual overall gain you get.  Then that signal will go through the linestage of your preamplifier, which according to data posted by Chakster, adds 7db of gain, for a total signal voltage of about 0.5V.  Depending upon the input sensitivity of your amplifier, that might be close to enough if not quite enough to make your listening experience a happy one.  (To make these conversions of db to V, I use calculators available to anyone on-line.  You should learn to use them too.)
I don't at all agree with the insistence of a few that a SUT is always superior to a high gain phono stage, but if you do choose a SUT, you MUST connect it to the MM input of your phono stage, which we know yields 43db of gain.  The difference between your high and low gain inputs is therefore 15db. 15db of gain is equivalent to a voltage gain difference of 5.6X.  You want a SUT that adds more voltage gain than that, because you already know (pending further info about your amp and speakers) that 58db is not enough.  Your cartridge, which has an internal resistance of 5 ohms, according to someone, will work fine with a SUT that has a 1:20 turns ratio (a voltage gain of 20X).  That combo of 43db gain from your MM stage plus a SUT with a 1:20 turns ratio should put you in a safe area for total gain.  1:10 might work too (voltage gain 10X).
I think why many others think 58db should be "enough" is because most linestage sections add more than 7db of gain on top of the output of the phono section, more typically 10 to 20db.  That may be why the consensus is you should have enough gain already.  Plus we don't know about your amplifier.
Many cool ideas here to consider. To help clarify, my equipment:

Rega P2 with Dynavector 20x2L
Bluesound NODE 2021
Rogue RP-1 preamp
Rogue Stereo 100 Power amp
Fyne Audio F301 bookshelf speakers
Polk Audio powered sub
Blue jean cabling
Room is 12’w x 18’d x 9’h

I also want to say I’m not dissatisfied with the sound coming from the TT rig, just wonder if it can be improved with a couple more db. Perhaps 60db or 61db etc. I do not ALWAYS crank the volume. Volume goes to 60 on the Rogue RP-1 and its usually set to 45+, when I get to the upper settings is where I hear a faint background noise. It’s manageable.

Some additional specs for equipment:

Stereo 100
100 wpc
input sens. 1.0 V rms

RP-1
gain 9.5 db (The gain on the post above was incorrect or revised in according to the manual that came with my new unit 2021)
output impedance 725 ohms
phono gain 43db, 58db
phono overload 45 mv

Speakers
89db
8 ohm

Right now I have the Pre phono gain set at 58db and resistive loading set at 1K ohms.

Really appreciate your input, learn a lot on this forum! I wonder if I am splitting hairs here, but then again look at the hoppy we are in ...lol


What would you do??
Oh, and I tried to use a couple of the online calculators. Kinda steep learning curve for me right now but I believe the KAB calculator suggested 61db gain. Am I missing anything with a 58db to 61 db difference? I’m sure some of you more seasoned audiophiles have been down this road before!

If someone with more knowledge than me can help me out with the math: With my set up, is my TT plus Pre producing enough input V to the power amp? Do I have to crank the volume because there's not enough input?
I thought I covered this in my earlier post.  We mentioned that 58db of gain applied to the 0.3mV output of your cartridge would yield a ~0.24V output from your phono stage.  Adding to that the 9.5db gain of your linestage would result in a net signal voltage output from your whole preamplifier of ~3 X 0.24V = 0.72V.  (9.5db translates to about 3X voltage gain.) The calculation gave a different result the first time, because I was working with a putative 7db gain from your linestage, as opposed to 9,5db.  Given that we now know the sensitivity of your amplifier is 1V and also given that you disclosed the fact you use powered subwoofers, which presumably relieves your main amplifiers of the power demands required for deep bass response, I would say you ought not to be suffering from lack of gain adequate to drive your speakers. 


"Faint background noise" can be what is known as "tube rush".  Sometimes that happens when you crank the gain on your tube preamp, which you are not really doing.  Maybe your tubes are going weak.  Also, was Chakster correct in stating that your phono stage uses two 12AU7 tubes, only?  If so, there has to be either a SUT built into the MC input stage OR there are solid state devices adding gain.  You cannot derive 58db of gain from two 12AU7s alone. Below is a useful website.

http://www.sengpielaudio.com/calculator-gainloss.htmhttp://

@lewm 

Thanks for breaking that down for me! So sounds like everything from the cartridge through to the power amp matches up well. Could there be any improvement by getting closer to the full 1 volt rating? By the way, I use a powered sub, but the mains are still running full range off the power amp. The sub is being fed by the preamp. You probably already realize this just wanted to point it out. It's my understanding that to relieve the mains of the work of producing deep bass you need to add a crossover or filter? Again, still learning all the different setups. If I remember correctly the RP1 uses a tube output stage, the phono stage may be solid state, I'll have to look into that.