Can you believe this?


I went through my garage the other day & pulled out my old Phase Linear 8000 Series II turntable.
I knew I had it, but didn'd know which box it was in when we moved here over 4 years ago.
I had not used it in about 20 years & had gone through 10 or 12 high end turntables in that time (Garrard, Nottingham, Oracle, Clearaudio, Avid & Verdier) just to name a few.
First I took it down to my man cave & cleaned it up.
Then I started to set it up & realized I might have a problem.
The patch cords (RCA) needed cleaning - So I cleaned them with alcohol.
Then I attached the RCA jacks to my phono stage (Pamphili).
Next was to attach the Pamphili to the pre amp (Einstein II) which has only balanced inputs, so I got out a pair of RCA cords & attached the RCA to XLR adapters & thought all was going fine.
I powered up all the components & hit the start button on the turntable & the arm started to move in a very weird way (tracking to the right).
I thought I had leveled it properly, but I guess I was wrong.
After trial & error for about 20 minutes with some good ole Kentucky leverage the table was properly balanced.
I pulled out my favorite Doc Severensen LP & was ready for a listen.
I didn't know what to expect next, but another problem arised - Music was only coming from the left channel.
First I removed the headshell & checked the connection to the cartridge (Ortofon MC 20) & all seemed well.
Next was the connection between the cables & the RCA to XLR adapters & that seemed fine.
Now I had figured out that the 30 year old cartridge was at fault - I had my ZXY Universe SSB handy & figured what the hell - A $5K cartridge on a $800 turntable?
To my dismay - Left channel only again.
OK - It must be the RCA cables between the phono pre & the pre amp.
I get out another pair of RCA cables, attached the RCA to XLR adapters, connect everything back together & am hoping that it's not the RCA jacks that lead from the turntable itself.
VOILA! The turntable cued properly to the first cut & both channels were producing music.
To my amazement the sound was spectactular!
To say I was "FLOORED" is a gross understatement.
I pulled out Billy Joel (An Innocent Man Half - Speed Mastered), Melissa Manchester - For The Working Girl), Huey Lewis - Sports - Half Speed Mastered), Jackson Browne - Lawyers In Love) & was up until 3:00 AM celebrating with some Hennessey XO & trying to figure out why some of my much more expensive (turntable, cartridge, arm & phono pre) didn't put this 30 year old turntable & arm to waste?
Meet the new boss - Same as the old boss!
I always knew that I had kept this gem of a turntable for a reason & did not sell it when I sold all my Phase Linear gear over 20 years ago - Now I know why!
Some of you must think that I must be out of my mind, but I have had some $25K turntables, $10K tonearms, $15K cartridges & $12K phono pre amps & what I am now hearing is almost as great (90% - 95%) as anything I have owned prior to putting this old relic back into my system.
It's almost a shame that I thought that newer & belt drive & high mass was the only way to go when I had this Japaneese direct drive linear tracker sitting around & unused all these years.
When i get a chance - I'll try the original Ortoforn MC 20 again & see how she sounds as I bought it back in the day when I got the 8000 II.
Maybe I'll give the $15K Clearaudio Insider Reference Wood a shot too.
Now my wife can put her new car in the garage & I'll be in my listening room putting on one LP after another.
That's my story & I'm stickin' to it!

128x128paladin
An old audio and Phase Linear guru friend of mine has one. He swears by it, and although I'm deep in the old idler drive camp I can't fault the sound which is spectacular. Gongrarts on rediscovering your turntable.
Norman

Paladin, Before something bad happens, I strongly recommend that you replace all the electrolytic capacitors in your Phase Linear/Pioneer turntable.  After all this time, and after being stored unused in your garage, especially, odds are that at least some of those capacitors have gone leaky (electrically speaking if not also fluid-wise), and this can lead to damage to transistors and ICs in the circuit.  Some of those ICs will be hard to find if needed.
If you can find a service manual on the internet, it will likely have a parts list, which will include all capacitors and capacitor values. You can then use that list to order replacement electrolytics from an on-line company like Digikey or Mouser or Newark.  The total cost of such a purchase is not likely to exceed $20 to $30.  If you can solder, you can do the rest yourself.