2. cables
  3. 127506-1644

Need recomendation for an IC to fill out and enrich the sound between amp and pre-amp.

Don't what level  to start looking for a quality IC compatible IC with a Conrad Johnson PV-14L pre-amp and a BAT amp to fill out the sound.  I opted for an all RCA pre-amp because I got a good deal on the CJ, and did not want to wait for a mixed BAT XLR and RCA pre-amp, or that of another brand.  I did a lot of looking over 4 months

So the advantage of lower noise using the XLR to XLR interconnect is no longer in play, and I am still using a Signal Audio Cable XLR to RCA to connect the amp to the pre-amp.  It cost about $59, not that price matters. It sounds good with the components, BUT, I think I can buy a much better  RCA to RCA  IC that will deliver a much fuller and richer sound.   As good as Signal Cable IC is, it seems to lack a fullness in the lower to middle midrange, and also the soundstage could be wider and deeper. 

I realize it could be the CJ pre-amp or the mix of CJ  which is 10 years old but was upgraded to the SE version Despite what I said, it sounds very good. 

Therefore, I would like recommendations for an interconnect that may accomplish what I described above before getting on "The Cable Company loaner library IC merry go round.  A  $200-$300 "USED" price range is my budget.   Thank you, SJ     

 

sunnyjim
sunnyjim OP
927 posts
 

Almarg.  Thank you again for the information about the Jensen Transformer

I have 3 ways to go; 1) BAT no lower has adapters, and suggested Cardas adapters. Victor K. at BAT did say I was better off with  "what I have now" that is, the Signal Cable that is RCA (out) to XLR input.  Therefore,  I think he endorses the concept of a mixed connector IC, then using adapters 

2)  JW Audio Cable emailed me back regarding its ad on AG which show a Reference series IC for $329, or the Signature series IC for $149. Both are 1M and can be configured the same as the Signal Cable I currently use.

3)  Jensen Transformer with their cables which are Canares Star Quad. The question comes down to which solution will deliver the best sound and provide the most compatible connection.  The adapters are only a last consideration and are not inexpensive. Parts Connexsion sells the Cardas adapters for about 82.00 a set and I will need two sets. (I think) plus $6.00 shipping


Obviously, the Jenson transformer with appropriate cables will cost $300-$350  So it is a toss -up between the JW Audio Reference cable , or the Jensen device  Let me know if you have any other  thoughts on the 2 solutions, should you have the time. I am not in a hurry and it is not crucial.  .  SJ

  


almarg's avatar
Ag insider logo xs@2x
almarg
9,670 posts
 
3) Jensen Transformer with their cables which are Canares Star Quad.
Hi Jim,

First, to be sure it’s clear you can use any cable brand with the Jensen transformer. And you needn’t use the same brand for the RCA cables and the XLR cables, for that matter. The particular seller of Jensen transformers I suggested just happens to also sell many Canare cables.

I would strongly suspect that the Jensen transformer option will make the most difference, among the options you listed. And I would expect it to be more likely than not that the difference will be in the right direction, from a subjective standpoint. It is also conceivable, though, that the difference may be in the wrong direction, subjectively. But if that were to occur I would interpret it to mean that the root cause of the problem is elsewhere in the system. As I said earlier, a Jensen transformer, which would provide the BAT amp with a true balanced pair of signals, is IMO the right way to implement this kind of interface, at least within anything close to the price range you are considering.

Good luck. Regards,
-- Al

hemi04
57 posts
 
Purist Audio Design Corvus cables very full midrange 

ggc
178 posts
 
Happy Holidays Sunnyjim,
Invest in cables made by Thales. It is undoubtedly the last pair of cables you will ever buy. I agree with those who are suggesting an outside transformer, rather than a XLR to RCA configuration. I am not just saying this because I happen to have two pairs for sale. Once I heard these for myself, I changed out all of my Transparent and Stage 3 IC Cables, which were 3-4X more expensive. I now use them exclusively for IC and Speaker Cables. CJ is also very friendly for tube rolling - as others have pointed out. By far one of the best investments I have ever made.
www.tonarm.ch

mtrot
804 posts
 
I bought a pair of these Cardas XLR to RCA adapters to connect my XLR only Krell amp.

The sound seems to be fantastic with my High Fidelity CT-1 interconnect.  By using these adapters, you can use any cable you want, and you can easily swap out cables to evaluate them.

http://www.dedicatedaudio.com/products/cardas-gold-premium-cga-male-xlr-adapters-xlr-male-to-rca-fem... 
More to discover