Mapleshade Silclear


Category: Accessories

I'm not a big proponent of the "WOW" factor, meaning very few tweaks have caused me to go "WOW". The wow ones include rebuilding my McCormack DNA .5 amp to near Rev A, changing the caps in my speakers from Axon's to Sonicaps, and few others. Now that doesn't mean I don't hear differences and improvements with other tweaks, it's just that I don't believe in overemphasizing these differences into religous revalations and such.

So, Silclear doesn't fall into the "WOW" category with me, but it did make an improvement in my rig. The simplest explanation of these changes I can make goes like this. Have you ever cleaned the contacts on your interconnects, speaker cables and power cords after a year or more of ignoring them? Did you hear the improvements in transparency and quieter backgrounds? Well I just cleaned everything over the New Year's holidays with cotton balls and alcohol with an application of SST (to signal wires) and Pro-Gold (to electrical connections) afterwards. Now, in February I applied Silclear to everything in my system that has a plug, jack or socket. This means interconnects, speaker cables, fuses, all electrical jacks inside my amp & CD player and DAC, electrical cords, tube pins, phono cartridge pins, etc. The difference was as if I left all these connections to tarnish for a year or more and then cleaned them all again.

Now, given that I just did the cleaning I can conclude that Silclear took this one step farther than alcohol and SST. Things were more transparent and noticeably punchier. The bass was louder (dammit - I had to turn down the sub's volume and rebalance the bottom end again). Soundstaging and imaging seemed to be a slight/tiny bit more forward than before, maybe because things seemed a bit louder at the same volume settings. Tonally everything was still balanced, just more there in terms of detail and nuance and definition. But I also found that there was a sense of more "realness" to instruments, especially cymbals (hearing more brass with the zing), and voice (more in the room presence), and piano (more body and weight). The system sounded quieter too - i.e. blacker backgrounds (but this can also vary by time of day as the power grid changes).

Is this a "wow" review in disguise? Perhaps for many it is, but I already have a whole lot of transparency and realness in my system (see "Isn't Anything Stock?" for my system details). I now have more of that than before.

I really can't report that there were any bad aftereffects of the Silclear either. There's no way to undo the application easily (it's a grease), so there's no A-B testing available. So many tweaks improve on thing at the expense of another - not here. It's a good thing (thank you Martha Stewart, now go directly to jail and don't pass "GO").

Enjoy,
Bob
ptmconsulting
I talked to Pierre at MapleShade today. At the risk of being inaccurate, he feels that SilClear can never become an insulator, as suggested earlier in this thread. The only explanation he had for degradation would be that the product was put on too thickly at the beginning and then migrated with heat over time to cause a short within the system. BTW he was very nice and very interested in people's experience with the product. Hope this helps
Joe
I used Silclear very sparingly and for over a year had no adverse effects until now. That brought me back to this thread and after reading the posts, cleaned all interconnects with Caig and viola! Bright, clear, detailed, you name it. I guess the effect was gradual and I didn't hear it until I bought some new speakers and wondered what the hell was going on. Muddy and closed in and sounding like a table radio now and then. Great vocals and acoustic timber and tone but weird at the same time. It would vary. Now everything is fine and I just use the Silclear on power cords and tube pins.
Nonoise and anyone else who would like to comment. I am going to clean off my Silclear from anywhere it might migrate causing shorts becuase I think that I am hearing a degradation and am awaiting new speakers and want all to be cherry.
I started using kerosine as recommended by MapleShade and the Silclear comes of easily. The Deoxit people say that their product will not cut through grease. I am then using deoxit after the kerosene cleaning.
My question is how are you cleaning the RCA plugs, both the male and the female parts. I have sprayed deoxit into the female part, and used fine point swabs on the male. Is there a better way. It is very tedious. Thanks
Gammajo:

I've heard that kerosine or gasoline is the way to go if it is applied thickly.
White gas would be best but its hard to find nowadays. I initially put Silclear on very sparingly so I just used Caig Pro Gold G5 and sprayed it directly onto the male contacts and into the female contacts and wiped if off with a clean cloth and used cotton swabs where I could. Nothing too intricate and time consuming and all came out just fine.
I thought I had detail and info aplenty but now its a different story. As for the migration of Silclear, there's nothing really to worry about as long as it wasn't liberally applied. If there were to be a short, it would have happened already.
By the way, I'm going to repeat the whole process in a month or two just to make sure I get any residual effects. The best thing is not to panic and just go about cleaning the contacts as you would normally and all will be okay.
Good luck.