Running Two REL Subs off One Amp - Possible?

Howard, there are a few ways to run two subs off one amp.

For example, if you have a receiver, you can run a single interconnect from the sub-out on the receiver to a line-in on sub number one. Then you run a second single interconnect from the line-out on sub number one to the line-in on sub number two.

Another example. You can run a pair of interconnects from the pre-out on a pre-amp to the line-in on sub number one. Then run a second pair of interconnects from the line-out on sub number one to the line-in on sub number two.

The wiring also depends upon whether you run the left and right front speakers full range, or whether you are filtering ouput in the sub. But I won't get too complicated with all the combinations because I don't know what type of amp set up you're using, receiver, or preamp-power amp or even what the connections on the REL sub are.

I can't offer any opinion on the side issues you raised other than to say it was always my understanding that the subs shuld be separated, with each one close to each of the speakers.

Thanks, Mark. I'm running separates - McCormack RLD-1 preamp and DNA-125 amp.

Now that I think about it, I believe I read in an online owner's manual that the recommended method for two subs and one amp is to use the line output on the first sub.

Howard

If your amp has bi-wire outputs you could run the right sub from the right outputs, (connect the two positive and one negative) and the other from the left output. I don not believe that using the line level output is going to let you adjust the crossover for integration into your two channel setup. If you are using these only for HT, the processor would obviously set the crossover. I currenlty an only using one Rel but down the road would like to add another.

Howard: I have the McCormack RLD-1 preamplifier also, just like you (with the DNA225 Power Amplifier, both of them recently upgraded to Platinum Edition by Steve McCormack) and I am also thinking on Dual Subwoofer. Why are you running your subwoofer from your amplifier instead of using the RCA at the back of the RLD-1 preamplifier ? is there any acoustic advantage plugging the subwoofer at the back of the amplifier instead of going from the preamplifier ? you could use the right chanel for one subwoofer, left channel for the other subwoofer. By the way, I am considering Dual SVSound PB12 Plus/+2 or a single PB12 Ultra + 2, what do you think is the best option ? My speakers are Ambience Superslim 1800se Ribbon speakers and the rest of my system includes Metronome Signature Transport and d.a.c., Acoustic Signature Final Tool Turntable, Magnum Dynalab MD100TR Analog Triode Tubes FM Tuner, with high-end power cords, interconnects and speaker cables. Looking forward your comments. Best, Antonio Machado.

I use a REL and have been thinking of perhaps adding another, not so much for bass as for balance. I am using the Neutrik connector (I think this is called high-level connection?) in which the SW draws nothing but the faintest signal from the amp.

I would think doubling up the connections (ie the second sub) should be fine. But have not tried it.

Regarding position, this is one reason I have not gone to two subs yet. I am on a suspended wooden floor (basement below) and have noticed, when this down-firing sub is away from the walls it excites the floor more - simple physics, as there is more flex to the floor the farther you get from the anchor point, ie the wall). Of course, this would indicate that a corner would do best in that regard, but that excited too many room nodes, and I ended up with it a few inches from the left wall, and about 3 ft from the left speakerm, more or less in a plane with the speaker baffles.

Am concerned that bringing the sub too close to the speaker would cause some 'bounce' in the speaker (mine are not too heavy - only 60 lbs) and smear the sound from the mains.