The fallacy of ac treatment

Elizabeth - while current capability is an issue, one of the reasons why a dedicated feed works is that there are less connections on the line to pick up noise, and so one of the benefits of using the air conditioner's outlet is that it is the only outlet on that feed line. I am not implying you did not realise that - just clarifying.

Power conditioners , better cables & Power cords do make a difference... At the very least they lower the background noice, which may be the reason for a lot of the other noticed improvements. Surge protection is not a bid bonus too! I have a monster hts 3500 , the power amp goes directly in the wall! Audioquest quietlines are a nice item also!

I challenge the fact that you can hear the difference in power cords. The job of a power chord is to supply the transformer inside your piece of gear with alternate current of sufficient quantity to allow your device to operate properly. Inside your component, the power supply converts the alternating current to direct current. The direct current is then sent to power your circuitry. The power supply is where the filtering of your power occurs. Manufacturers use large capacitors and/or voltage regulators in the power supply to filter any residual AC or noise. The power supply design of your equipment is much more critical than an expensive power cord. The cleaner you make the direct current voltage feeding the audio circuits in your equipment the better your equipment will perform. The only exception to this is if the power cord is not of sufficient gage to supply the current necessary for your piece of gear to operate or if the power cord does not provide a good enough ground path to avoid voltage drops which causes system noise due to ground loops, assuming your AC wall outlet is grounded properly.

When I first heard of the power cord controversy, I was likewise skeptical as you are. Based on your assumptions, what differences could there be? The problem lies with your assumptions: 1. The power supply is where filtering of your power occurs. How does an amplifier know what to amplify? The answer is that it doesn't. It will attempt to amplify all signals presented to it. That includes an entire spectrum of radio frequency signals below and above it's normal operating range. Do you follow AudioAsylum? If not, perhaps you should. There is significant material on this issue. One "inmate" who like myself has Acoustat electrostatic speakers complained that something was causing his amplifier to shut down. He speculated that there was a malfunction within the high voltage Acoustat transformers. He later discovered that the villain was his old Monster speaker cable which had oxidized. It was now conducting high frequency hash which the amplifier doggedly attempted to amplify and overheated in the process. After hearing this, I examined the internal wiring of my transformers. Though my main speaker cable is new DH Labs silver wire, the Acoustat transformer has 15" of Monster cable internally. I discovered the same horribly oxidized wire. Once I replaced it, I was amazed at the difference in signal clarity. From Sade to Saint Saens and Madonna to Mozart, I am how hearing more inner detail. Similarly, a power cord can be quite effective at radiating RF energy. Better cords posess shielding that minimize this effect. 2. Manufacturers always install cords of sufficient gauge. Not. All wire loses signal to an extent. All components with anything less than 14 gauge cord is sacrificing power transfer. I will refer you to this more studious explanation: http://www.audioasylum.com/audio/cables/messages/13538.html Finally, one must consider one's point of reference. A casual listener will likely never hear any differences. Or someone who has a typical $2000 mid-fi system. The differences are readily heard by those who listen to music more regularly and those who have access to better equipment. Does your frame of reference include hearing what a $200,000 system can sound like on your music? It is both enlightening and frustrating at the same time. There is so much detail on discs most folks will never experience. Though my system costs something less than 10% of that amount, both speaker and power cords do make a difference. BTW, I don't (yet) have any $500 designer cords in my system. I have replaced four with industrial grade Belden 14 gauge shielded cable with quality Leviton plugs. Cost? About $15 each. I have dedicated power outlets for my system. Additionally, I use a Monster Cable HTS-1000 power conditioner on my front end components. The results are a cleaner, quieter background allowing more detail to be revealed and more powerful dynamics. Try it. You'll like it.

You bring up some good points that I did not consider but I am still the skeptic. I whole heartedly agree that the larger the power cable you use, the better off you are! It is safe to say at our relatively low voltages of 110 vac or 220 vac the larger the conductor the less opposition to current flow or resistance (at much higher potentials you deal with the skin effect where current flows on the outside of the conductor only). If we look at Ohm's law, a current flowing through resistance will cause a voltage drop. The amount of voltage dropped is dependant on the electrical resistance (or impedance with alternating current) and the current flow. Any drop of voltage across the power cord is detremental to system performance and frankly dangerous due to heat generated in the power cord itself (remember Power(heat)= V (voltage drop in the cord)x I (the current flowing). The second point I agree with you is on EMI (Electro Magnetic Interference). There are 2 types of EMI we must deal with: Radiated and Induced. The sources of these type of interferences are common to our everyday life from vacuum cleaners to our television sets. Unfortunately the best power cord in the world will not help with induced EMI as the interference is induced on the power source itself. This is the case for a dedicated outlet for yours audio system. There are caveats with this also. If one chooses to use a dedicated outlet the ground at the outlet is the most important consideration. I propose that the ground wire that is enclosed in the piece of romex feeding your outlet may not suffient depending on how far the outlet is from your breaker panel (remember what I mentioned about wire size and resistance). This can be checked by by measureing the neutral to ground voltage under load at your outlet. It should be almost zero volts. If it is not there is a voltage drop and this could be a cause of noise in you system. Radiated EMI is quite another story though. This (in my opinion) has more to do with good design in your component than a very good power cord. Shielding, ground planes on circuit cards etc. have more effect on this than the power cord. The only rule of thumb here is to keep everything as short as possible. If the EMI is higher in frequency, shorter leads make a poor antenna to pick up this. Remember that if the interference is 1 MHz or less a sufficient antenna would have to be over 100 feet long. A power conditioner may help with some of these problems but I submit as an electrical engineer that fancy power cords and power conditioners are not a good substitute for good electrical design and a little thought. Thanks for the reply. Audio sometimes becomes an emotional issue, and it is my pleasure to correspond with someone who is willing to talk about some of the scientific principles behind these issues.