2. speakers
  3. 157353-24

Upgrading Kef R100 crossovers

I just picked up some R100’s and am really liking them.  I think that I like them enough to try to squeeze every ounce of performance out of them and am thinking about upgrading ghe crossovers.  There are only a few components so I don’t think that it would cost too much $.  I am not handy with a soldering iron so I’d rather just send the crossover schdmatics to someone and have them send me back complete, new crossovers that I could just plug and play.  

Where / who could do this for me?

And while I am at it, would replacing the batting inside with some no rez be an improvement too?

Thanks ahead of time for any info on this!!
128x128b_limo
14 responses Add your response
b_limo's avatar
b_limo OP
2,274 posts
 
I contacted madisound and gave them the Kef R100 crossover schematics (that kef promptly emailed to me).  
Josh from madisound got back to me in a matter of 5 minutes with options and pricing.

wow!  Great service from kef and Josh from madisound 👍👍
highend666
352 posts
 
Danny at GR Research is one of the best and their all new copper caps are said to be the New Holy Grail of Caps!
kenjit
1,771 posts
 
Get yourself a magico and stop complaining. 
Post removed 
kenjit
1,771 posts
 
I’m surprised you aren’t supportive if me custom tuning my speakers for my ears

Get yourself a dsp crossover and get retuning then. 
oldhvymec
5,101 posts
 
Danny at GR Research is one of the best and their all new copper caps are said to be the New Holy Grail of Caps!

Have you priced those caps? Cost prohibitive, for sure The coppers, 5uf 100v 200.00 +  20uf is over 400.00 discounted.. 100 volt cap.. There a lot of great XO caps. Danny has more than one selection, or quality of cap, I'm sure, I hope!

Maybe the band pass xo for the mids/highs.. It could cost 2k for a 4 ohm 3 way.  100 volt... man oh man..

Regards
Post removed 
b_limo's avatar
b_limo OP
2,274 posts
 
@kenjit , do you have any recommendations regarding dsp?  And I don’t have the money really to buy extra amplifiers...

also, do I bypass the crossovers in the speakers altogether then?  I’m trying to send the signal through higher quality components...
b_limo's avatar
b_limo OP
2,274 posts
 
@bryhifi , I’ve seen contradictory statements within a single response.  It was something about mdf being junk, then 4 sentences later he said it was great.

Kenjitt, like my Mom, can argue with themselves as well as we can 🤷🏼
kenjit
1,771 posts
 
you could get the hypex plate amp or mini dsp plate amps. You will need to find a way to mount them either into the cabinet or onto it externally. Then you start tuning the speakers. You select various slopes, crossover points and time delay. You compare the results by ear. You adjust the eq too. You will need to put in a bit of baffle step compensation and a gentle downward slope. 

Yes you bypass the passive crossovers. 



b_limo's avatar
b_limo OP
2,274 posts
 
@kenjit , Thank You Kenjit, I will look into it 👍
audiokinesis
2,737 posts
 
Kenjit wrote:  " you could get the hypex plate amp or mini dsp plate amps. You will need to find a way to mount them either into the cabinet or onto it externally. Then you start tuning the speakers. You select various slopes, crossover points and time delay. You compare the results by ear. You adjust the eq too. You will need to put in a bit of baffle step compensation and a gentle downward slope. " 

Very helpful and complete reply!  Nice job - seriously! 

Duke

b_limo's avatar
b_limo OP
2,274 posts
 
@audiokinesis , I know, right?  I do respect the guy for not really ever stooping  to level I do with the insults. Maybe I can learn something from Kenjit after all 🙂.


audiokinesis
2,737 posts
 
@b_limo , I agree with you, and definitely respect Kenjit for the restraint he shows as far as not "replying in kind". 

Duke
Log in to respond
More to discover
80x80
PS Audio Aspen FR20 Loudspeaker
80x80
Kharma Exquisite Extended Ref 1a
80x80
Magico M2