Trans-Fi Terminator Tonearm: 2019 Update

Actually I suggested Nylon Pins to Vic, not saying Owen didn’t have the same thought though. I was discussing the Chatter based distortion with Vic, with the then steel pins running direct on the Aluminium "V" of the Strap. I mentioned I was going to remove material from the Strap and line it with Silicon or Nylon. Vic thought this would add to much extra complexity/cost to his production. So I casually mentioned an alternative could be Nylon pins, as they are available off the shelf and just need a point adding. I never actually liked the idea myself but Vic ran with it and it did cure the chatter. I always felt the pivot bearing needs a firm almost sharp point to work best. The Nylon is a bit to soft in my opinion.
I like your thinking, but I think anyone, not just design professionals can see the benefits of keeping things simple. The low tech approach of the Terminator has less to go wrong or maintain.
Actually I would have designed the mounting and VTA system completely differently. To me the fundamental flaw with the Terminator is the single pivot bolt that locks off the VTA adjustment and the Manifold/Slider levelling. Adjust one and you effect the other, I would have had separate methods of adjusting each.
But it is what it is and it kind of works so I can live with it. Designs are never finished, Vic still tinkers with his, as do I, its all part of the fun and it keeps the old grey matter ticking over.
Tip:
The Screws for levelling the Manifold/Slider are very sensitive in their adjustment, I tend to get it somewhere close, lock off the pivot bolt then do the final adjustment using the feet on my deck. It only takes a fraction of a turn on the feet but it is much finer adjustment and I can get the Slider to float stationary much easier this way.

Sound:
I tried with/without the Copper mat and preferred it with the Copper.
I put the Technics/Terminator with a lowly AT33PTG II up against my heavily modified Lenco idler drive with original Mission 774 arm and much more expensive VDH MC One Special. I preferred the Technics/Terminator.
I put the VDH in the Terminator and this confirmed it was the better set up.
I love the sound and my mods make the arm nicer to use, its the best sound I’ve had from Vinyl. See more comments Here:

@qwin 

On the  newer version of the Terminator that I have, all pins are made of nylon, including the pins for leveling the arm. It would be too difficult for me to take up your tip on leveling the arm using the turntable footers for final adjustments. I will stick with the old fashion way.

Your critique of the Terminator is appreciated. While we’re at it, add non-repeatable VTF adjustments as an additional criticism. I don’t know how you do it, but I fine tune VTF at the start of each listening session.

‘I was not familiar with the Vdh MC 1 Special so I read up on it. A reviewer described it as having similar sound signature as a Lyra Clavis dc. And your description of the MC 1 + Terminator combo sounding like music mirrors my vinyl experience. Especially these past two years, I was able to sourced two TOTL cartridges, a Transfiguration Proteus rebuilt by Anna Mighty Sound and A ZYX Ultimate Astro serviced by VAS audio. I no longer use my critical faculties to judge what I hear. I don’t break it down into distinct low, mid, and high frequencies, weighting their individual qualities, and analyzing how they interact. There is just this continuum and coherence that is felt as music, no artifice. These are cartridges retailing in the $6k-13k range playing on a +$1k arm, entry level phono stage, with terrific results. Who would have known? 
 

It’s a pity so few will hear this arm. I am in a prolonged process of acquiring a second, higher tier, pivot arm. And I believe I will be in a better position to taut the abilities of the Trans-Fi arm when compared the additional pivot arm. In any case, it was a SME V that preceded  the Terminator and the upper hand belongs to the underdog. 

i have a question for you: in working with the pivot pins, both you and Owen mentioned chatter induced distortion. I thought I knew what that meant. But I cannot be sure. What does a chatter induced distortion sound like, which frequency range does it occur? 

@ledoux1238
The distortion, was vibration feeding back through the stylus/cartridge into the Wand/pins. When steel pins were running in the Aluminium "V" of the straps this vibration caused them to wiggle about or chatter. This noise or distortion could be heard through the playback as a break up of the trailing edges on vocals etc. Vic added weights over the pivots to try and stop this, which was partially successful, then went to Nylon pins as a more pliable contact point, giving some degree of damping, which worked better. I went for steel pins running in Nylon "V" which I think works better still, both sonically and in a practical way, as the pins can be pushed into the Nylon, making a small depression and they stay in these, rather than slide along the "V" in use.
Yes setting the VTF is a pain with these disc weights, but sonically better than the original boss and threaded rod with a screw on weight. This was easy to adjust but didn't sound as good. I reset my VTF yesterday and it took me about 20 attempts to get the 1.42g I wanted, must have knocked the wand out of position 3 or 4 times in the process. I set the VTF with the air off and I get repeatable measurements. If yours is varying, I would question your wire dressing, it may be causing slight drag.

@qwin

i tried over the weekend to work on repeatable measurements for VTF, Ito no avail. I usually measure with air on. This was discussed in an earlier post. But even with air off, I am +-0.02g. And the readings with air on and off are different. I looked carefully at the way you dress the wires, I do it quite close. My gauge is one that has a plate right on the platter, but made in China, I assume due to its price. This aspect of the arm’s operation still eludes me. 

@ledoux1238 
0.02g is a tiny amount, but I am getting exactly the same reading every time.
There is a blue sticker in the centre of my scales measuring pad. I do get slightly different readings outside this zone. I stand my gauge on a wood block next to the platter, it brings the measuring pad up to the exact height of a record on the platter.
I am using VERY light and flexible wire, which has improved things in this area. When I used the silk wrapped Litz wire, my readings were all over the place.
Check out my blog for details of the wire I use.