speaker sensitivity dividing lines

Unsound: In the days of yesteryear where sealed designs walked the Earth in great numbers, there were TONS of speakers in the 85 - 88 dB range. Since driver technology has increased over the years, vents of one kind or another are FAR more common and many designs "share the load" with multiple drivers covering the same pass band, efficiency has crept up a bit over the old school "one driver per passband" sealed box of yesteryear. From what i've seen, I think that most speakers are in the 88 - 91 dB range nowadays. I could be wrong though and that's why i asked for other points of view. Sean
>

Gs: Correct me if i'm wrong, but you can only put so much signal into any gain stage before it begins to distort and overload. On the same hand, an output stage can only put out so much power before it starts to distort and overload. As such, driving the piss out of ANY part of the system is going to result in distortion being fed to the speakers and your ears. Obviously, it might sound a lot louder ( distortion of any type typically increases "apparent volume" ) but you are still limited to X amount of signal at a "relatively clean" level. I do agree that tubes overload more gracefully ( with less "nasty" distortion ), which allows one to push them harder with less listening fatigue though.

Having said that, I don't think that ones' electronics has anything to do with the sensitivity rating of a pair of speakers. Whether or not said electronics will drive a set of speakers to "good" or "comparitively loud" levels is another story. That, as far as i can tell, is food for another thread. Sean
>

Ernie: That is a good point about "optimistic" specs from manufacturers. I think that Klipsch did just that with their RB-5's. From what i can remember, they claimed something like 95 - 96 dB's and they actually measured more like 91 - 92 dB's ( give or take ). While 91 - 92 dB's for a small bookshelf type speaker is a pretty respectable level of output, NO amount of break-in or "test procedure differences" could account for the 3 - 5 dB difference in rated specs vs measured performance in my book.

Then again, many people do not realize that speakers can and do play louder after the drivers are fully broken in. The stiff suspension due to a driver being new reduces both excursion capabilities and therefore reduces output. As such, a driver should really be used under normal conditions for a good period of time before actually trying to "spec" it. New "out of the box" figures will rarely jive with what one ends up with after a good amount of actual use on a pair of speakers. I have seen JA state similar things and even mention that he didn't think that the speaker was fully "broken in" when taking measurements, but he did test and publish the results just the same.

As far as your comments go about comparing speakers with "equivalent" sensitivity ratings, tonal balance / frequency response can drastically affect what we perceive to be "apparent volume". That is why i said that the sensitivity should be rated and averaged over a BROAD frequency spectrum, as this approach would tend to minimize differences in readings where one speaker was very peaky in specific areas and another was pretty even across the band.

Too bad "audio standards" really aren't "standardized". Sean
>

Phasecorrect: Have you ever actually watched / measured how an amplifier loads into a speaker and how the speaker can modulate the amplifier ? In some cases, you can literally watch the input waveform from the preamp or source change as the amp has to deal with the reflected EMF of a speaker. This can vary as signal amplitude changes i.e. the harder that you drive the speaker, the more reflected EMF that you have to deal with. Obviously, some amps will deal with the reflected signal a LOT better / differently than other amps. This is not to mention the amount of crosstalk that is generated between channels in such a situation. If you or anyone else think i'm nuts, try talking to ANY electrical engineer worth a salt and see what they have to say. As to whether or not this is audible, you betcha. The fact that many people may not have ever really noticed this probably has more to do with the fact that most speakers present relatively "benign" or "easy" loads and the amplifiers aren't being worked to death in such situations. That does not mean that such occurances don't take place on a regular basis though for some of us with reactive speakers.

As far as my thoughts regarding sensitivity of a speaker go, i never implied that one should delete "low" efficiency speakers from their list or only consider speakers of "reasonable" sensitivity. My thoughts in trying to work with this is that many newcomers don't understand that there is such a thing as "matching" when it comes to building a quality component system. All things being equal, starting off with a more efficient speaker will typically make amplifier selection a little easier and open up more available options. If they knew that a speaker was considered "less sensitive" as compared to others, they might be able to make a more informed decision as to the suitability of said speakers and amplification choices. I was NOT saying that this is the most important spec, only that it is one of several factors to look at.

For the record, i have speakers that are 2-3 ohms that are appr 82 dB's output. I also have 3-4 ohm speakers that are about 85 - 86 dB's output. If i had only used speakers that were 8 ohms nominal and 90+ dB output, i would be in a world of surprise in terms of wondering why my amp sounded "bad" ( clipping with lack of control ) and the speakers wouldn't play very loud. If i had some type of a chart to compare sensitivity / output levels of various speakers, i would know that if i went noticeably down on efficiency, i would have to go up on power output to achieve the same spl's and level of control. However, if i stayed within a dB or two from old to new speakers, i might not notice a big difference. Granted, there are other variables here that could come into play, but i'm talking "simple" stuff here for those that aren't that "audio educated", not trying to teach the world physics in one thread or post.

Try to keep things in perspective. If we could cram all we needed to know about each subject into one thread, there would be no need for these or any other forums. I'm still learning and i hope others are too. Sean
>