@zlone the moderators blocked the other listing that you sent me on the AG site,
Could I to send it to navyachts at h o t m a i l
dot com
Thanks!
Some Cables Thoughts
Working on those cable suggestions you all have offered up to me in the past. I was wondering if any of you might know of a decent grade 110V power cord that has a 90-degree male connector on it? Something like this:
https://www.cablesdirect.com/store/p/2128.aspx
If not, a super flexible cable something similar the stock one that came with my Coda amp, that can turn downward asap and not to long of a connector itself, some are supe long. I need to get tight to the back wall.
As fair as speaker cables, I was thinking of a pair of these, 6 feet long with spade ends.
https://kimber.com/customize/12TC
Do I have your blessings?
PS: No one speaks much here about XLO cables. There are these on USAM - 6ft for $600 DIY terminations, I’d just use bare wire (if I could figure it out (lol)
https://www.usaudiomart.com/details/649981370-xlo-signature-3-54-bi-wire-shotgun-speaker-cables/
There is another set there as well with bananas for $800, but I prefer spade.
Thank you!
Showing 26 responses by navyachts
@curiousjim please check out my system here on AG. PC would be for all 4 major components. Under $500 for PC Under $1000 for Speaker Cable, unless you can provide argument for spending more. @bigtwin thanks!
|
@audphile1 will do, thanks! |
@audio_is_subjective busy first day on the job, you'll go far with that handle of your here...LOL Welcome! |
@gkelly Wow, that's perfect, thank you! |
@bigtwin I just checked out their website, great tip, thanks! |
@audphile1 sure, I can make some cables. Which one would you suggest? https://www.furutech.com/products/bulk-cables/power-cables-bulk-cables/
|
@audphile1 awesome, thank you! @soix +1 |
@jetter Thanks, I already saw this and have communicated with the seller at ASAM. I really only need a 6-foot pair and the seller suggested that they are quite thick and it won’t be so easy to loom/hide the additional length, so I think I’m going to have to pass on them. UGH! |
@audphile1 now if I could just find a 6 foot set! |
@jetter I think I’m going to give the Satori’s shot |
@audphile1 @soix thanks. Next, I’ll start working on those power cables! |
@kennyc ok, let me check it out, thanks |
@bigkidz I have purchased the Audio Zen Satori's as recommended by @soix @audphile1 @jetter. They just arrived yesterday so I hope to give them a test drive later today. Then onto the power cable dilemma! I'll need a cord for my music server, DAC and pre-amp. The power amp will be the tough one though, as the Furutech outlet is dead center behind the p. amp and I'd like to get the amp as close to the wall as possible. Hence my query on the 90-degree male end for a DIY application. I still need to contact VH Audio about this. Oh ya, and then there's the power conditioner. I found this one on USAM: |
@soix thanks for the lead on the CPT units, I will check out that link! Some also mentioned Shunayata, they have some reasonably price PCs as well. Talk about buying locally, they are just a couple of hours down the road from me, although I don't think they sell direct. |
@audio_is_subjective great handle! I will bone up on this, thanks.
|
@audphile1 I am working on upgrading my cables and I wanted to ask you about your network connections. You speak highly of your Purist 7 CAT cable, which is pretty pricey, so I was wondering how you connect it to your music server. Ideally it would be nice to go straight from the modem to the music server but then you’d have no other connections to hook up ethernet cables to. Right now I’m going: modem>switch>router>music server. If you throw in the FMCs add another cable. But I was trying to mimic your set-up by eliminating the FMCs. That would be 3 ethernet cables at over $1,000. I could cut it to 2 cables though buy just going: modem>switch>music server which would cut me down to 2 Purist 7 cables. I am only running a Netgear switch (modem & router too), would I then need to upgrade the switch to that of a higher quality to match the quality of the Purists cables? Any advice on this would be much appreciated, thank you! |
OK, I will order the balance of my cables tomorrow. Thanks for the clarification. I just noticed a lot more base with the new cables at this point. We’ll see how further changes influence that. It’s kinda like going from the renderer in the R26 DAC to the Aurender N200, did I hear a difference, yes, but a $4,000 difference...no. I still think I need to tweak my DAC. @yyzsantabarbara recommends the Schitt LIM and you and @ghrdprentice recommended the cord TT2. It’s easy to try the Schitt product because of their 15-day return policy, but with all the money I spent on cabling, I don’t think I’ll be able to swing for a new cord TT 2, so I’ll have to buy used, which will make it more difficult to deal with if it’s not too tasty! Then, would I also need their pricey Mscaler to boot? The only other DAC I would like to try is a W4S 10th anniversary DAC. I had one of the less expensive DACs with Martin Logans before and it sounded pretty darn good. Anyways, thank you for your continued help and support. |
@audphile1 Not using ROON any longer so I'm using both the Aurender app with some music on the internal hard drives. I also have my Tidal HiFi account linked up to it. Cables right now are both a DH Labs USB & coaxial. They both sound about the same but I use the USB the most. I have disconnected the FMCs and am using a run of the mill cat6. I ordered a Purist 7 from Cable Co today and will order Audio Envy power cords tomorrow. |
@audphile1 Another AG member recommendation. I’m backing off the DIY so I liked the fact that they offer 90 degree ends. I need 4 power cords, amp, pre-amp, Aurender and DAC. I haven’t ordered them yet, so still open to suggestions. They were just over $200 a crack. Will this suffice modem to router: https://www.amazon.com/gp/product/B08MXY9ZKS/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 |
Here's a few in that price range I've been looking at: https://www.thecableco.com/specials/forte-f3-powerchord.html https://wyred4sound.com/products/p-1-ultra-power?variant=28622119698506 https://silversonic.com/products/power-cables/encore/
|
@audphile1 I stuck with the Audio Envy 2’ power cord for the amp because I got both male and female male, in the 90° figuration. That will allow me to get the amp close-up to the wall. I looked at the Audience Forte F3 and there are a great price as you suggested, but they’re a little bit long and I don’t think for the music server, DAC, preamp, need such a heavy duty cord. The F3s are 10 AWG. I’m thinking probably a good 14 AWG cord would be sufficient for these pieces, so still on the hunt! |