Master M,
Check it out..
I would PM you but it will delete the address.
I've added just water, and just 3 in one oil mixed to a paste. I dried my stuff with a heat gun. The water based worked GREAT if you didn't remove the artifact and reinstall or reverse the direction in the case of a fuse or breaker. The 3 in one worked better.
You can make a QUART of enhancer for 22.00 usd.
Sell your goodies for 35.00 a tiny bottle and FUND a 50,000.00 stereo system.. Who says we can't think BIG.. That 22.00 will make that much enhancer.. I bought 4 10 ounce bags 10 years ago for 120. usd Enough for 5-7 GALLONS..
I've also used Nuclear Never Seize and added about 1/4 to the amount being mixed. 1/4 dust, 3/4 NNS, mix and thin with 3 in ONE, one drop at a time..
SEE I share..
Because the effect of graphene as a SUPER conductor requires a single layer to achieve 1000% conductivity increase, I'll settle for 100% plus if I can get it by applying the product below..
Think THIN...
OK Master M., that will being your system up to 522.00 plus the cost of 3 in ONE.. I had some laying around.. :-)
<<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>>>>
2 items 2.2.oz each 100 % conductive carbon Graphene powder : Extra Fine
https://www.ebay.com/itm/153433640674
<<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>
To all the naysayers.. 22.00 usd. My gift to you...
Enjoy.. MOCK if you must... BUT it works pretty darn good..
Dip a bare wire in it, install the wire into the barrel of the terminal and 20-50 tons from a press OR a single hammer strike to set the terminal to the cable end and a second one to WELD the two.. You can't get better contact.. I use an old speedo cable dye and a 6 pounder. Don't hit it a THIRD time, that will loosen it.. 20-30 ton hammer strike, YUP...
Regards
Check it out..
I would PM you but it will delete the address.
I've added just water, and just 3 in one oil mixed to a paste. I dried my stuff with a heat gun. The water based worked GREAT if you didn't remove the artifact and reinstall or reverse the direction in the case of a fuse or breaker. The 3 in one worked better.
You can make a QUART of enhancer for 22.00 usd.
Sell your goodies for 35.00 a tiny bottle and FUND a 50,000.00 stereo system.. Who says we can't think BIG.. That 22.00 will make that much enhancer.. I bought 4 10 ounce bags 10 years ago for 120. usd Enough for 5-7 GALLONS..
I've also used Nuclear Never Seize and added about 1/4 to the amount being mixed. 1/4 dust, 3/4 NNS, mix and thin with 3 in ONE, one drop at a time..
SEE I share..
Because the effect of graphene as a SUPER conductor requires a single layer to achieve 1000% conductivity increase, I'll settle for 100% plus if I can get it by applying the product below..
Think THIN...
OK Master M., that will being your system up to 522.00 plus the cost of 3 in ONE.. I had some laying around.. :-)
<<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>>>>
2 items 2.2.oz each 100 % conductive carbon Graphene powder : Extra Fine
https://www.ebay.com/itm/153433640674
<<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>
To all the naysayers.. 22.00 usd. My gift to you...
Enjoy.. MOCK if you must... BUT it works pretty darn good..
Dip a bare wire in it, install the wire into the barrel of the terminal and 20-50 tons from a press OR a single hammer strike to set the terminal to the cable end and a second one to WELD the two.. You can't get better contact.. I use an old speedo cable dye and a 6 pounder. Don't hit it a THIRD time, that will loosen it.. 20-30 ton hammer strike, YUP...
Regards