Pass Labs XA30.5 in my system?


Dear Audiophiles!

I am looking for a solid-state class A power amplifier with balanced circuit topology to replace Acurus in my modest Hi-Fi setup:
 
Mac mini (USB3 output) ->
Singxer SU-1 ->
Yggdrasil DAC (AES/EBU XLR input) ->
Primare PRE30 preamplifier (AES/EBU XLR input) ->
Acurus A250 power amplifier (RCA input) ->
Monitor Audio RS-6
 
I am currently considering Pass Labs XA30.5 and am wondering if it will “work nicely” with my upstream and downstream components.

Any info/advice is very much appreciated. Please chime in!

Please see the specs below for your consideration.

Pass Labs XA30.5

Type: Solid-state stereo amplifier
Power Output: 30 wpc into 8 Ohm, 60 wpc into 4 Ohm (both 14.8dbW)
Power Consumption (Watts): 238
Temperature (deg C.): 53
Voltage Gain: 26 dB
Input Sensitivity: 0.77 V at 26db gain
Frequency Response: 1.5Hz–100kHz, –3db at 1.5Hz, –2db at 100kHz
Signal/noise: 150db at full power (I cannot believe this is not a misprint!)
Distortion: 0.01% at 3 watts, 0.1% at 30 watts (measured at 1 kHz)
Input Impedance: 30 kOhm balanced, 15 kOhm unbalanced
Damping Factor: 150 for an 8 Ohm nominal load
Maximum Output Current: 20 Ampere
Maximum Output Voltage: ±35 Volts
Output Noise: 150 microvolt unweighted 20 Hz - 20 kHz
DC Offset: <50 mV
Slew rate: ±50 V/µs
Dimensions: 19" (485mm) W by 7" (180mm) H by 19" (485mm) D
Weight: 62 lbs (28kg)
Shipping weight: 75 lbs (34kg)

Primare PRE30 Preamplifier

Balanced inputs          560mV
Line inputs                   280mV
Sensitivity adjustment    -20dB to +20dB
Tape outputs               280mV
Gain                            16dB
Frequency response    DC to 100kHz ± 0.1dB
THD                             <0.01%
Signal-to-noise ratio    -118dB
Crosstalk                      -113dB
Mains                            100/115/230V
Dimensions (WxDxH)    430 x 410 x 100mm
Weight                           9.5kg

Monitor Audio RS6

Frequency Response: 38 Hz - 30 KHz
Sensitivity (1W@1M):   91 dB
Nominal Impedance:     6 Ohms
Power Handling (RMS): 120 W
Recommended Amplifier Requirements (RMS): 40 - 120 W
Tweeter Crossover Frequency: 3 KHz
Drive Unit Compliment: 1 x 6” C-CAM® Bass, 1 x 6” C-CAM® Bass Mid-range. 1 x 1” gold dome C-CAM® tweeter.
Cabinet Design: Balanced velocity twin reflex ported
Product External Dimensions: (H x W x D) 850 x 185 x 250 mm
Plinth Dimensions: (H x W x D): 25 x 255 x 305 mm
Individual Weight: 18 Kg

N.B. Impedance varies with frequency and goes to as low as 4 Ohms and as high as 16 Ohms. And, most importantly,“real” sensitivity is much lower than “nominal”: 87.40dB (averaged 300Hz-3kHz, 2.83V/1m)!
Measurements taken in the anechoic chamber at Canada's National Research Council can be found through this link:
http://www.soundstagenetwork.com/index.php?option=com_content&view=article&id=1221:nrc-measu...

hardball

Showing 1 response by waltersalas


For a lot of us, once you go tubes, there is no turning back. I made the foolish mistake a couple or three years ago of getting rid of all my tube gear and buying a Devialet--which is an attractive, very "nice" sounding, user friendly, all-in-one solution--and within six months, I found I was just not listening to the music very much. As good as the Devialet was, it just did not have that tube magic. 

Bottom line, I sold it and started over, and now I am back in the tubes--and back to listening to music far too long into the night. I agree with Wolfie that the Jolida is a very nice amp. I had a 3502 for a while and really enjoyed it. Eventually I moved on to a Line Magnetic 508ia, which is the best amp I have ever owned and better than I could ever imagine an integrated sounding. The 518ia and 219ia are also excellent, and I have seen the 518 in the classifieds recently. Might be worth looking into, as most of the people who get them seem to like them as much as I do.

I am not sure what your budget is, but somewhere between Jolida, Primaluna, and Line Magnetic (just to name a few), you should be able to find something that will tickle your ears and touch your heart.