Mono Bridged Setup - cable ends not long enough?


Hello,

I am looking to set up a bridge with 2x McIntosh MC252's connected to a pair of B&W 802s. I'm not prepared for a bi-amp setup just yet - taking baby steps... (Feel free to flame and tell me how stupid I am - but taking advantage of the extra power is the exclusive objective right now)

For cables, I'm looking at a pair of AQ Comet single bi-wire speaker cables (these claim to be a good solution for bi-wiring since "When the halves are separated at the speaker end, the Double Star-Quad Geometry turns Comet into a true Double-BiWire set thanks to the magnetic autonomy of each Quad-conductor section."

Down to the actual question. In order to run in bridged mode, the McIntosh manual requires that the Loudspeaker (-) is connected to the left output (+) and the Loudspeaker (+) is connected to the right output (+).

The problem is that the L and R posts are on opposite sides of the amp, almost a foot apart. I don't know of any 'jacketed' audio cable that has the (-) and (+) connections that extend far enough beyond the jacket to reach those two posts.

What am I doing wrong here?

thanks!

Andrew
andrewdanapoole
Blue Jeans Cable would be a perfect source for a custom cable like this that would be affordable. Get their 10 awg, it is good quality stff.
You may want to get some basic cables just to test the 2 amps in your system first. When you bridge amps, it has an effect on sound quality that most people don't like. I'm not saying that will definitely be the case in your system, but its something to consider.
Thanks all, appreciate the input! What causes the impact on sound quality with bridging?
"10-11-14: Andrewdanapoole
Thanks all, appreciate the input! What causes the impact on sound quality with bridging?"

Its one of those things that you have to try for yourself. Even if we both bridged the same amps, its likely we would get different results depending on the rest of the components in out systems. Its also worth noting, that there are some amps that are known to sound very good when bridged. In my experience, I liked both BEL and Bryston when bridged. Actually, I thought the BEL sounded better bridged.
What causes the impact on sound quality with bridging?
There are probably a number of factors which contribute to that, to varying degrees depending on the particular amplifier and speakers. Including:

1)Most amplifiers will have lower distortion when driving higher impedances (e.g., 8 ohms of more) than when driving lower impedances (e.g., 4 ohms or less). As I indicated earlier, in bridged mode the amp will see the speaker's impedance divided by 2.

I suspect that effect will be mitigated to some extent in the case of your particular amplifier, because it includes autoformers having 2 ohm taps (which I suspect you would find to be the best choice when bridging with a 4 ohm speaker), as well as 4 ohm taps (which I suspect you would find to be the best choice when bridging with an 8 ohm speaker).

2)As you probably realize, speakers commonly have impedances that dip to considerably lower values at some frequencies than their nominal rated impedance. In many cases that happens at bass or mid-bass frequencies which typically require a lot of energy. Again, in bridged mode that impedance dip will be seen by the amp as half of its actual value, and the result may be too low a value for some amps to handle with good results.

3)Since in bridged mode both of the channels in the amp participate in the generation of the same output signal, to the extent that the two channels don't have identical characteristics distortion may be introduced in bridged mode that would not occur in stereo mode.

4)In bridged mode a phase inversion has to be applied to the signal on one of the amp's two channels. In some designs that will necessitate insertion of an extra active stage into the signal path, with possible adverse sonic effects.

There are probably other factors that may be involved as well, but those are some that readily come to mind. Despite all that, however, as ZD indicated it is certainly conceivable that there will be some cases in which an amp will sound better in bridged mode than in stereo mode, at least from a subjective standpoint and in the context of some specific systems.

Regards,
-- Al