2. amps-preamps
  3. 1382836646

Mola-Mola Kaluga Ncore-based Monos: An impression

Interested as I am in trending and promising advances in high power amplification, I sought at RMAF new amplifier designs based on new class D modules like Ncore NC1200 technology and its derivates… Hence my specific interest in listening to the soon to be released Mola Mola Kaluga monoblocks for the first time.

The amps, driving a pair of YG speakers, were in a nice double sized room... 535(?), I believe... This room has no bizarre acoustic interactions, so systems can perform under good conditions.

The differentially balanced Kaluga monoblocks are based on a version of the Hypex Ncore modules, which have been customized by Bruno Putzeys for these devices. Mr. Putzeys is both creator of the underlying Ncore technology, as well as the lead designer of the Kaluga amps. I do not have detailed specs yet, but Kalugas should output approximately 400W/8, 700W/4, and close to 1KW/2 Ohms. Peak current should be in the general neighborhood of 40A. Each half width chassis feature two sets of Furutech binding posts for biwiring, an XLR and an RCA input connector, and a 15A Furutech IEC connector. A small temporary contact switch for standby/operating is in the middle of the front plate.

In case you wondered what the Mola-Mola name comes from… Mola-Mola is a sunfish… The largest bony fish in the world... A lovely oceanic swimmer that can weigh over 1500 Lbs. Hmm, but what about Kaluga? The mighty Kaluga instead is a majorly large sturgeon fish native to the frigid Amur River… Fact is that Kaluga may be the largest fresh-water fish in the world. So, it was not a total surprise when I realized that the shape of the half width chassis of the compact Kaluga amp, seamlessly assembled from thick slabs of complexly machined aluminum slabs, is very much in keeping with the Neptunian theme... The top is broadly wavy, and starts to sweep downwards towards the front of the unit... Where it meets the front faceplate, which is gracefully concave instead... The whole gives the impression of a stylized breaking oceanic wave... Intentional or serendipity? I do not know... Must ask Bruno about it.

The unusually looking Kalugas may be compact, yet they sound as mighty as they feel solidly hefty. The amps drive the big YG with elegant musicality, firm ease, and loads of resolving harmonic richness that extends from deep bass to high treble without obvious constrictions... In the best Ncore tradition, Kalugas never break a sweat with the demanding YGs, and have no problem reproducing bowed 7th cords in my test string sextet (introduction to Dvorak Op. 87) with enchanting finesse and without obvious cross-modulating distortion... a feat that is sadly so painfully difficult to accomplish by many SS and tube amps of classic topologies.

The Kaluga monoblock amps by Mola-Mola are expected to be released by CES 2014... At $15.9K, my highly preliminary impression is that they will prove very strong music performers, congruent with my general goldilockian sonic goals… Definitely worth examinin them in much greater detail.

Here is the US distributor:

On A Higher Note
(949) 544-1990
Contact: Philip O’Hanlon

Saluti, Guido
guidocorona

Showing 6 responses by guidocorona

guidocorona OP
4,298 posts
 
Hi Vicdamone, thank you for joining... 'Twas getting lonely 'round here *grins!*

Your mention of the NC400 in your homegrown monos reminds me that I should ask Mr. Putzeys about circuit differences between the DIY and OEM version of the Ncore modules. The Kaluga circuit is designed around modules that are apparently enhanced versions of the NC1200 created for OEMs.
guidocorona OP
4,298 posts
 
VicDamone, the SMPS1200 and its 400 counterpart use machine-controlled surface mounts to minimize circuit path lengthand optimize QC. I am not sure if Kaluga utilizes the basic SMPS1200 like Veritas, or a more sophisticated SMPS1200 derived implementation specific to Kaluga... I will eventually find out.

G.
guidocorona OP
4,298 posts
 
Hi Bob, I am not terribly surprised about the sonic enhancements that you experienced with the implementation of heavier chassis for your amps...

Case in point... The half width Mola-Mola chassis weigh a bit over 20 Lbs each... They are not made from a single block because of the complexity of the shape and the different textures that Putzeys wanted to impart... The chassis is instead formed by a small number of assembled slabs. Bruno Putzeys appears to believe in mechanical isolation by fastening the modules inside a solid non resonant mass... So does Merrill with Veritas... Rowland has been segregating electronic circuits into pockets carved inside milled chassis probably for the last 15 years.... Including the M925 monos in my system.

But the benefit may not be only one of mechanical isolation... According to Rowland and Merrill, the benefit is also one of RF isolation from/to the outside, as well as minimization of RF / EM contamination among various internal chassis pockets.

G.
guidocorona OP
4,298 posts
 
Good point Bob... Are you talking about the Ncore NC1200 engineering demonstrator amp that Hypex circulates among interested OEMs?

Apologies for appearing dense... I am blind and my JAWS screen reader cannot decypher photos.

Guido
guidocorona OP
4,298 posts
 
Hi Bob, the internal construction of the Kaluga may differ considerably from the HYPEX Ncore engineering demo for OEMs... I have not had the opportunity of opening up a Kaluga, but I suspect there might be more internal segregation and RF isolation than on the technology demonstrator. Guido
guidocorona OP
4,298 posts
 
Al, you are absolutely correct... The underlying module is but one component out of a myriad of factors that affect the final sound... Otherwise, by extension, just about every KT-88 amp would sound the same, wouldn't it *grins!*

At RMAF, room 537 suggested that Kalugas sound is quite intriguing... There exists a general family trait shared with the sonics of other Ncore NC1200 amps that have graced my system... Like the Merrill Veritas, and my Rowland M925 reference.

of course, a couple of hours of listening in a system with unfamiliar ancillary electronics, speakers, wires, acoustics, and undefined break-in state of any components, cannot yield much more than... "I am intrigued" and hope to assess the potential of Kaluga in my own system!

Until now, all Kaluga amplifiers shown in the US have been prototypes... Either with temporary metalwork, or engineering-level innerds, or... Both. The device(s) at RMAF may have been the very first samples with finalized innerds and metalwork to reach the US. Hopefully, around CES 2014, the creature will be off to the races.

G.

More to discover