How do I get good sounding, clean electricity?


A'goners, I am about to build out my basement for a home theater and I have the chance to do the electicity and wiring properly. However, I'm not sure what "proper" is.

Does anyone have any thoughts on what makes for good clean electrical power? Should I set up seperate circuits from the main (which I am doing anyway). Should I use any special copper wire, connections or outlets, what about this cryogenic thing, conditioners, etc. I'm in the US with 112 volts.

I'm not too anal (yet) but while building out the basics if there's anything wise to do first, now is the time.

As always, my sincere thanks for any input.

Kevin
arbrnrngr
Here are some links I've noted for when I attempt my own AC project -

>http://forum.audiogon.com/cgi-bin/fr.pl?fcabl&1100220439&openflup&73&4#73


http://forum.audiogon.com/cgi-bin/fr_memb.pl?actghtech&1&listflup&zzSean

http://forum.audiogon.com/cgi-bin/fr.pl?htech&1051595901&openusid&zzSean&4&5#Sean

http://forum.audiogon.com/cgi-bin/fr.pl?htech&1097628057&read&keyw&zzisolation+transformer+ebay

http://www.audioasylum.com/audio/general/messages/355063.html

Research xentek or topaz isolation transformers. Also maybe twist the in-wall wiring every meter to help with RF rejection? Also research into "balanced power."



http://home.comcast.net/~thomasw_2/

http://www.htguide.com/forum/archive/index.php4/t-3584

ThomasW
We're going to use a chassis (p/n 14-19103x) from Par-Metal (http://www.par-metal.com)

http://www.par-metal.com/10s01.jpg

Here's a pic of the transformer

http://www.hometheaterhifi.com/volume_10_3/images/plitron-isolation-transformer-front-main.jpg

Here are a couple of links to tech papers detailing balanced power for those interested

http://www.equitech.com/articles/origin.html
http://www.equitech.com/articles/widescreen.html

ThomasW
We're still waiting on Plitron, but have been ordering the other stuff needed for the project. Here's a break down.

Chassis Par-Metal #14-19103C $112.80. Clear anodized, not as cool looking as black but hides dust well , (important priority for bachelor living :D ). For those wanting a lower buck option, PE has a same sized chassis that lists for $77 p/n 262-434. This has thinner metal than the Par-Metal chassis. If one goes with the PE chassis then plan on reinforcing the bottom with a layer of Masonite to support the weight of the transformer.

Below are the Mouser.com items we ordered. The 693....... is the Mouser part number

First item below is a 20 amp on/off switch, second item is a 20amp IEC 'power entry module'. That means an IEC AC inlet combined with a high current RFI filter. Using this eliminates the need for a shielded power cable.

693-ABDBL200C0 Schurter TA45 BLK ROCKER 20A $15.41
693-C20F.0001 Schurter FRONT SCREW MT 20A $26.39

These are the 2 values of EMI/RFI filters. The smaller amperage is for front end gear, pre-amps, CDP's etc. The larger 20 amp filter is for higher draw devices like projectors, power amps, receivers. etc.

693-5500.2041 Schurter 1-STAGE STD 6A FMW $ 9.58
693-5500.2047 Schurter 1-STAGE STD 20A FMW2 $ 17.58

The following power cord part was ordered from BrigarElectronics.com

H320C Hubbell 20 amp IEC Female connector $6.95

The actual power cord wire was ordered from PE it's the Carol 12 gauge. PE p/n 100-577 $11.60/25 ft

We've nixed the idea of a 'soft start' device. Smaller transformers let's say 1000va, can be powered up using a simple thermistor. But using one of these isn't a good idea for larger transformers. The reason being that once on they stay on until cooled down. As a result if there's a temporary power loss the Thermistor doesn't have time to cool down and reset. We could use a relay circuit, but that in our opinion will add needless cost and complexity to the design.

To be continued.....

But from time to time Equi=Tech has closeout sales (http://www.equitech.com/products/seconds/seconds.html)

ThomasW
If you haven't already checkout the other balanced power projects on my website.
http://home.comcast.net/~thomasw_2/CheapskateBP1.html

Also here's a link to Glen's DIY design
http://www.villagephotos.com/pubbrowse.asp?selected=923645

Should give you some ideas about construction and assembly

Sorry for the beginner question but what about plugging a light bulb into this?
AL Garay,
Plugging a lamp into a balanced power unit is quite dangerous.
Standard residential differential power from the wall consists of a +120 volt lead and a neutral lead. The neutral lead is bonded to ground in the loadcenter of your house.
The AC plug on a standard lamp is keyed so when it's plugged into the wall it ensures the base of the bulb is connected to neutral and the pointy business end of the bulb gets the +120 volts.
When you or your family is messing around changing a burnt bulb, they have no way of knowing that the lamp may still be turned on. As they unscrew the burnt bulb, it is highly likely their hand comes in contact with the metal base of the bulb itself. Luckily it is connected to neutral.
Guess what happens if it was plugged into a balanced power unit. The base of the bulb will be at 60 volts..... :(
brucek

Aaron
Anytime you open walls it is good to run some empty conduit for future runs of coax, optical or other communications-type interconnects that you might want to hide in the walls at a later time. There is easy-to-use light weight conduit for just this purpose.
Well thank you all of course and I will do more research but the multiple circuits and quality connections, etc. are all wonderful thoughts. All much appreciated.

Kevin
I have run 2 dedicated 20 amp lines using 10 guage shielded stranded copper wire(water proof).The ground wires of these 2 lines are grounded outside the panel buss directly to the copper ground wire that goes to the panel by means of a copper connector that was there when I had cable tv.The plugs are Hubbel, one line to a Hydra 2 for the power amps, and one to a Furman Balanced power conditioner for my pre, CLS11Z speakers, turntable. I have my cd player on a common house circuit, which I plan to change to a dedicated circuit.I also use Foundation Research line condioners on speakers, turntable,cd,pre-amp.With so much dirt in the lines you can't have enough filtering.