I have a Simaudio Moon 110LP phone preamp amplifying a Dynavector 20X2L cartridge on a VPI Classic. It feeds in to an Outlaw Audio RR2160 amp which drives Magnepan LRS speakers.
I recently moved and two months in I realized my speaker placement wasn’t quite right, so today I reorganized my listening room. This involved unplugging some power cables but I kept most of the interconnects in place. I did have to disconnect the phone stage from the amplifier.
After getting things back into place, I listened to some music using coaxial input before reconnecting the interconnects of the phono stage. When I tried to, I actually got some electric current that burned my hand slightly. This came from the back of the amplifier. I made sure everything was unplugged and tried again - this time a spark and smoke from the interconnect making contact to the back of the amplifier.
I’m so confused why this would happen, but eventually I did get everything connected. Now the output from the phono stage is just a bump every 1 second. It doesn’t amplify the signal from the TT.
My amplifier has a built in phono stage and using this I was able to verify that the turntable is still producing a signal. The built in phono stage sounds terrible, however, as thin and flat as paper. It is music, however.
When I connect the phono stage to the power, the blue light on the front illuminates for a moment and then goes dark.
Incredibly, when I was unplugging the phono preamp, I actually got some current from simply touching the exterior of the box. Something is seriously wrong and dangerous with my setup, and this box was grounded to the turntable with a ground cable, which was connected to the outlet with a three prong cable with ground.
Has anyone experienced anything like this before? I will email Simaudio and see if they’ll repair it. I’m also taking recommendations for replacements. I liked the 110LP and maybe will just replace with the 110LPV2.
I think I messed up on the DC measurements, i think they were AC. so let me try again:
SMPS (one lead in ground of OEM ITC, the other on the sleeve contact of the SMPS):
0.6 mV DC on V
0.0 mV DC on LoZ
SMPS (red lead center, black on sleeve):
18.15 V DC on V
18 V DC on LoZ
SMPS (one lead in ground of the OEM IEC connector of the power cord , the other on the sleeve contact of the SMPS):
0.6 mV DC on V
0.0 mV DC on LoZ
Multi-meter should have been set to AC voltage not DC. I am looking for AC mains voltage on the SMPS output power cord connector. The measurements would be good if only AC measurements.
.
SMPS (red lead center, black on sleeve):
18.15 V DC on V
18 V DC on LoZ
This is correct. Voltage looks good.
That doesn’t mean there is not a problem with the preamp. I believe there is. The Blue power light maybe saying there is.
Again, I would NOT connect the input or output of the preamp to any equipment.
Yes I verified your question about subwoofer in earlier comment today. The subwoofer pins are only two even though the power cord has three prongs. So I assume it’s ungrounded. But note the CDP is grounded and the amp is sitting on top of it and connected via coaxial cable.
Yes the sup amp is ungrounded. AC power wiring in the sub amplifier is double insulated.
So where was the spark fault current path? What is the source.
No doubt there is a difference of potential, voltage, between the output of the phono preamp and the RR2160 amp signal ground, (outer shell) of the analog input jacks.
Saturday, check for voltage from the outer shell of the output RCA jack of the phono preamp to the outer shell of the analog input RCA jack on the RR2160 amp.
Should of done that to begin with...
Both units powered on.
.
I think we are back to square one.
When you get a chance check the wall outlets the equipment plugs into for proper Hot / Neutral polarity and for equipment ground. At least you will be able to check them off your list.
I don’t remember reading a post where you responded to this.
If you did not read, measure, high voltage, or any voltage... Question... Is the SMPS 120Vac plug in blades the same width or is one wider than the other? Therein polarized. If both blades are the same reverse the SMPS 180 degrees in the receptacle and perform the test for high voltage again.
That is from the long winding thread I posted yesterday.
.
One other thing I didn’t think about yesterday. The tests for the SMPS I had you do for checking for AC mains high voltage on the output side of SMPS were unloaded.
I don’t know what I was thinking yesterday... I should of had you do the tests with the phono preamp connected to the SMPS. Therein the connected load. Likely a defective connected load that might be overloading the SMPS. A real world test...
Probably also should have had you use the wall outlet that the SMPS is normally plugged into. IF, one of the blades is not polarized, therein it could be plugged in either way, it would be plugged in the direction that caused the electrical spark fault event.
.
IF you want to try the test again.
Test procedure is a little different than yesterday.
You will still use the OEM 3 wire power cord to connect one of the mm test lead probes to the wall EGC. ( an extension of the probe lead)
1) Set up for the test.
Before the SMPS output power cord connector is plugged into the phono preamp.
Connect an IC (interconnect cable) into one of the RCA output jacks on the preamp. Extend the other end of the IC so it will be easy for you to touch the other test lead probe of the mm to the outer ground shell of the IC RCA plug.
2) insert the mm black test lead probe into the female EGC ground contact of the plugged in OEM power cord.
3) Set mm to "V". (mm will default to V AC.)
4) Plug SMPS output power cord connector into phono preamp. (Blue light starts doing its’ thing. Preamp has DC power. SMPS has a load on its’ output)
5) Touch mm test lead probe to the outer ground shell of the IC RCA plug.
What voltage is measured, displayed, on the mm? No need to check for LoZ voltage. The connected load of the preamp is more than enough load. LoZ would only add a small additional load.
6) Check again for a voltage reading after the blue light on the front of the preamp is no longer lit for any difference of voltage measured.
7) Just to cover all the bases... Repeat the test measuring for DC voltage. You probably should let the phono preamp do a reset by disconnecting the SMPS power cord plug from the preamp. Just trying to cover all the bases.
At some point i was going to buy an outlaw amp but I read a thread that a few people said it caught on fire I would not plug that back in .I don't rember it being an audiogon thread.this could be destructive to all your equipment.be careful.
You must have a verified phone number and physical address in order to post in the Audiogon Forums. Please return to Audiogon.com and complete this step. If you have any questions please contact Support.
