2. speakers
  3. 165901-160344

Connecting Bose 901 Equalizer to a receiver or another graphic equalizer

Greetings!  I've read a lot of the discussions posted; contacted Bose, Yamaha, Sony, and Kenwood, and still can't figure out how to reconnect my 901 EQ to my system.  Before I moved, the EQ/speakers were connected to this system and worked wonderfully.  My receiver does not have pre-outs but it does have tape play/record and so does the Kenwood EQ.  If someone can assist, I'd be very grateful.

I see a lot of people do not like the 901s.  When I graduated high school and joined the Air Force in 77, I purchased 3 pairs of 901s in Okinawa JA because at that time I loved them.  The pair I kept all of these years are the special edition oak cabinets on stands.  Several years ago, I had the speakers (tweeters) rebuilt.  I have an emotional attachment to them now.  Thanks for your help!
bill901s
russ69's avatar
russ69
3,505 posts
 
Corrected, I think. 

"...the path to the receiver goes tape out of kenwood to tape in on the Bose EQ and then out of the Bose EQ to tape in on the Kenwood. Switch the tape monitor on and off and you can hear the difference.  If you get it wrong just switch one end of the interconnects and it will be right. 
oldhvymec
5,101 posts
 

Try the Bose community?

<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>

LOL This is the Bose community, just most of us changed 35 + years ago. They are still in the shop somewhere under silks, along with 20 + other pairs of retired, or in the process of being made speakers..:-)

OP it is "OUT IN, OUT IN. Out of the tape monitor into the EQ, out of the EQ and into Tape 1 or 2. Select the tape loop your going to monitor (1 or 2) and make sure your plugged in there. 1 or 2 (if you have two) And engage the monitor switch or button. Actual pre in or out is not the best way, that is NOT passive, it is in the path and active.

The cables, the wire inside and components were just CHEAP...

It's better to use tone control and see if the "LOOP" is better or worse. In the preamp path you can't disengage the EQ.. Your stuck with CRAP.. OK...

Regards
bill901s OP
3 posts
 
Thanks for the suggestions but I must be an idiot!  The back of the Kenwood graphic equalizer has line in/ line out. It has tape A and B REC and PLAY. I tried going from the Bose EQ tape out and tape in to all three of the options on the Kenwood EQ. When connected properly, I remember being able to push the tape monitor button on the Bose EQ and it would engage and disengage. I can’t get the Bose EQ engaged. I have a masters degree in education but I may need someone to speak slower.  Is the Bose EQ or the KENWOOD EQ connected to the Sony receiver or just to each other?  Does anything connect to the amplifier connections on the back of the Bose EQ?  I appreciate your time!  
rockrider
181 posts
 
https://www.bose.com/en_us/support.html

I suspect you have the Series III version, but it looks like they have all the owners guides there for you to find. 
You should connect your receiver to the “amplifier” connections on the Bose EQ. 
There are many ways to daisy chain in the Kenwood EQ should you desire to do so, but connecting to the Bose EQ “tape recorder” connections might be the most versatile. 
Good luck!

(I was a Bose fan in 1977 too!)
rockrider
181 posts
 
Sorry, please ignore my suggestion to connect the Kenwood EQ to the Bose EQ tape recorder connections if you want both EQs summed. (Surely Bose did not send EQ’d signals to the Tape connections.)
More to discover