Biamping Maggie 20.1s: Amps and Xover Frequencies


I am trying to optimize the sound from a pair of 20.1’s – currently driven by a pair of VTL 450 signature monoblocks (450 watts into 4 ohms). You’d figure that is plenty for the Maggies, but I am not totally wowed in the dynamics and openness category. I’ve heard that biamping makes them more dynamic and open, and want to try that route. To that effect, I’ve just ordered a Marchand XM-44 active Xover with 0.5 db attenuators, and am currently selecting modules. I’m also selecting an amplifier to drive the low frequency drivers. I don’t want to invest a ton in trying out this approach, but I want to make sure I am getting a sense of what it can do. So – my questions relate to amplifier selection for the bottom end and Xover frequencies.

For amplifiers, my price range is $2k-$4k, but I’d really like to stay near the $2k level for now and maybe upgrade later if warranted. Here is my current working list of amplifiers in approximate order of ascending price:

Bryston 4BSST
Bryston 7BSST
Innersound (not sure which model to consider)
H2O 250 Monoblocks
Parasound JC-1
McCormack DNA-500
Pass labs x350
Edge NL10
Pass Labs x600

I think I’d like to go with the Bryston 4BSST to start, but would like comments and other suggestions. The VTL’s would power the mids and highs. A digital amp would be great for power consumption considerations, and I know they do well on the bass (I’ve owned PS Audio), but still find myself hesitating a bit. More comments?

As for Xover frequencies, my review online indicates the following:

Stock high-pass (HP) is 6dB (first order) with a -3dB point at 230Hz
Stock low-pass (LP) is 18dB (third order) with a -3dB point of 116Hz

Recommendations include:

Increase LP to 140Hz (same 18dB slope)
Increase HP to 250Hz (same 6dB slope)

The second recommendation also included moving the LP to 110Hz instead of 116Hz, but I can’t imagine that 6Hz is audible in this case.

The Marchand Xover modules aren’t too pricey, so I intend to get the stock settings (230/6 and 116/18) along with a 140/18 and maybe a 250/6. Are there any other combinations out there worthy of trying? If I took a shotgun approach, should I stick with the specified slopes of the HP and LP units and just try different Xover frequencies? How much of a change is significant for both the LP and the HP (e.g. 10%).

Thanks Very Much, Peter S.
peter_s

Showing 1 response by ngjockey

Wow!

Some of those amps would be overkill just for bass. Besides, the Pass's impedance and sensitivity are quite different than the VTL. You could also consider something like the Carver Pro series. For the frequencies your talking, watts count.

I can't offer advice on the crossover specs except that lower frequencies are less noticeable, particulary with hybrids, but that isn't the case here. I have never suggested biamping over 150 Hz but the Maggies may be the exception. The Marchands are top notch, except that they don't have the adjustable phase like sub xovers, such as the Paradigm X30. In my experience with Genesis 350's, which have their own bass amp/xover, phase can be important in less than 90 degrees at a turn. Sorry, if that just adds to the confusion.

You're doing something more advanced than most and you seem to have a good understanding. Ya, removing the passive parasites makes it more efficient but the speakers were designed with them. Perhaps the only people that know more would be Marchand and Magnepan.

I hate to say this, because they're great speakers and amps, but perhaps you're expecting more than they're designed to do. Have you considered adding a subwoofer, or two? Just separating the extreme lows (say 60 Hz) might help in your quest and avoid evisceration.