best support shelf/isolation device for a rega p9?

I replaced the footer of my Rega P9 with TAOC TITE-35S. And rest it on their platform SCB-RS50G with TITE-25MF on the top shelf of Solidsteel 5.4 rack. They're as solid as rock and sound really good for me.

http://i32.photobucket.com/albums/d37/cannoncal/photo1.jpg

I am using the platform from Tekna. It works very well. Any kind of isolation is mandatory to the P9.

I am using a Target wall shelf with a black diamond racing shelf in place of the mdf one that comes with the Target under my p9(original series table with RB1000 arm in place of the RB900 that came with it). I took the stock feet off and am using stillpoints with the points up resting in the holes where the original screws were.

This works really well and I am getting minimal feedback on my system. Does not seem to suck any of the life out of the sound at all. My system is in between the speakers which is not ideal but it is still working fine.

The Rega or Target wall shelves would be your best bet I think.

I recently purchased and set up a P3-24, a few steps down from the P9. As such, I also looked for a value method to level and isolate the table. I have the table sitting on a open frame cabinet I built many years ago so needed way to level and isolate the TT for best performance.

After searching posts on the site regarding leveling and isolation, stole a couple of ideas and set up in the following way.

To level the table, I added a 14X18X1-1/2" thick cutting board with Soundcare isolation/levling feet installed. The Soundcare are integrated isolation points and flat surface protectors in one. The cutting board is the exact footprint size of the P3. Searched ebay to find a 14X18 cutting board. Was hoping for 2" thick, but 1-1/2 was thickest I could find. The Soundcare were a suggestion from this site and bought online from a company called Taylor. Ordering/delivery was quick and painless.

To further isolate the table, on top of cutting board I have 2 $15 keyboard gel type wrist restpads purchased at Staples with a $5 18X18 marble tile (didn't find granite the day I was at Home Depot). The gel pads are also 18" long. The turntable sits on top of the tile. The gelpad suggestion was also one found on this site. Works great.

I tried a variation of reversing the leveling table (cutting board) and isolation (tile and gel wrist pads) but the bass sounded tightest and overall soundstage much better with the Rega sitting on the wrist pad/tile combination. Might sound even better with a thicker granite top, but the tile set up sounds darn good. There is a kitchen remodelling store where I can likely get a sink cutout cut down to 14X18, but haven't had time to do that yet.

I've been enjoying the heck out of all the 30+ year old albums I babied through college have mostly been in storage in a spare bedroom until I replaced my old turntable with the Rega. In the short time I've had the table, have had it set up with and without the isolation. The sound is greatly improved by the gel pad/tile combo. The cutting board seemed to do less for the sound, but was needed to level as the P3 doesn't have any leveling capability.

Anyway, a low cost, not as bad looking as it sounds do it yourself isolation/leveling set up generated from ideas found on this site…. and for me worked great. About $50-60 for the feet, $25 for the cutting board, $30 for two gel pads, $5 for the tile. Had to drill and insert 1/4 thread adaptors in the cutting board for the Soundcare feet. About $120 total...

Thanks to those uncredited for the ideas I borrowed if you read this….

I recently traded my P7 for a P9 and am using the isolation table I had for my P7 - an Adona isolation table of Vibrapod/Vibracone feet.

http://www.adonacorporation.com/multi-element.html

http://vibrapod.com/

Has anybody tried replacing the stock feet with Stillpoints?

Maple blocks do work. I have my Scoutmaster on a 4" thick one siting on large Mapleshade cones. I have just heard the Star Sound cones and they work even better. I bought my block from Michigan Maple Block . It is very large and cost me $96 + $25 shipping. Timber Nation makes some that may be better, I have a smaller one of theirs. They are a very cost effective solution and look good also. Timber Nation has optional cone feet which are good but not as good as Star Sound , Mapleshade or other high quality cones.

I have a P-9. At the suggestion of my dealer, I removed the stock Rega feet and use Walker large cones/pucks. These sit on a 1/2 thick slab of solid steel plate with a soundcoated paint. this sits on the top shelf of my Solid Steel 5.4 rack. Rack's bottom points rest in brass receptors. I have had no problems with any kind of resonances/feedback.
I am told that the BEST way to isolate the Rega is to place it on the Rega wall shelf and mount that on the wall.

I own a P9 - great table. I tried a Symposium Ultra and it was awful (with Rollerblock Jrs in between). At loud volumes the table would pick up vibrations from the bass and it translated to a loud distorted hum. I contacted Symposium and they indicated that this might occur. Removed the Ultra and used a Brightstar AirMass with the Jrs in between - perfect!

The Rega wall mount is ideal and not all that expensive.

the ikea lack shelf when wall mounted. Is my idea of an ideal way to listen to this table. I would stay away from the sorbothane for all turntables it has a way of dulling sound.

the ikea lack shelf when wall mounted is my idea of an ideal way to listen to this table. I would stay away from the sorbothane for all turntables it has a way of dulling the sound.