Canare 4S11 is a standard. WHY? So the sound ISN'T changed by CABLE differences.. A wire is a single conductor.. Studio is about being "THE SAME" not different.. NY to CA
The 12 gauge CABLE is perfect.. Heavy copper with a good insulator/dielectric (no shielding other than the weave). That will give you the best BASS. I like OCC with teflon. LOL Not smaller for bass BIGGER. Add armor and tune the sound with terminal ends.. I like copper.. RED COPPER..
https://www.ebay.com/itm/HI-End-12TC-Speaker-Cable-OCC-Copper-Audiophile-speaker-cable-HIFI-Banana-p...
The cable is from China. I paid 108.00. You won't get this kind of performance, without spending a LOT of money.. I added red copper spades for 29.00 additional cost..
I also double the run with a silver clad OCC teflon RIBBON, for a whopping 68.00 dollar and I change the ends to silver over red copper and a saw spring tube banana.
https://www.ebay.com/itm/HiFi-Audio-Speaker-Cable-OCC-Silver-Plated-Speaker-Wire-Carbon-Fiber-Banana...
Under 300.00 + Tungsten add 45.00.
The copper cable is fork spade (both ends), The ribbon is spring/banana (both ends). Left and right side gets BOTH cables attached to the same terminals. They are NOT bi wired, just a double or triple of different wire types. You can move the copper to the bass post in a dual terminal setup.. I use that construct for silky smooth mids BUT a TON of detail is added because of the ribbon cable, Planars and Ribbons..
I add a 99.99% .014 tungsten stinger in an oversized silicone tube (+ side only). It depends on the drivers I use.
Monsoon planars I don't need tungsten, GR, and BGs do.. Most standard round drivers and domes like it too.. For 45.00 usd the tube and WIRE (single construct) can be added to the CABLE run..
LOL TRY to beat that combination, of dollars spent and performance gained.. ..10 day of cable conditioning on a Cable Cooker 2.5.
2-400 hours of BREAK IN, NOT BURN IN...on the silver/clad at LEAST.
The OCC copper weave, the first 2 hours will be the biggest change.. 24 hours of settling, that's After I cooked the heck out of them for 10 full days..
Regards
The 12 gauge CABLE is perfect.. Heavy copper with a good insulator/dielectric (no shielding other than the weave). That will give you the best BASS. I like OCC with teflon. LOL Not smaller for bass BIGGER. Add armor and tune the sound with terminal ends.. I like copper.. RED COPPER..
https://www.ebay.com/itm/HI-End-12TC-Speaker-Cable-OCC-Copper-Audiophile-speaker-cable-HIFI-Banana-p...
The cable is from China. I paid 108.00. You won't get this kind of performance, without spending a LOT of money.. I added red copper spades for 29.00 additional cost..
I also double the run with a silver clad OCC teflon RIBBON, for a whopping 68.00 dollar and I change the ends to silver over red copper and a saw spring tube banana.
https://www.ebay.com/itm/HiFi-Audio-Speaker-Cable-OCC-Silver-Plated-Speaker-Wire-Carbon-Fiber-Banana...
Under 300.00 + Tungsten add 45.00.
The copper cable is fork spade (both ends), The ribbon is spring/banana (both ends). Left and right side gets BOTH cables attached to the same terminals. They are NOT bi wired, just a double or triple of different wire types. You can move the copper to the bass post in a dual terminal setup.. I use that construct for silky smooth mids BUT a TON of detail is added because of the ribbon cable, Planars and Ribbons..
I add a 99.99% .014 tungsten stinger in an oversized silicone tube (+ side only). It depends on the drivers I use.
Monsoon planars I don't need tungsten, GR, and BGs do.. Most standard round drivers and domes like it too.. For 45.00 usd the tube and WIRE (single construct) can be added to the CABLE run..
LOL TRY to beat that combination, of dollars spent and performance gained.. ..10 day of cable conditioning on a Cable Cooker 2.5.
2-400 hours of BREAK IN, NOT BURN IN...on the silver/clad at LEAST.
The OCC copper weave, the first 2 hours will be the biggest change.. 24 hours of settling, that's After I cooked the heck out of them for 10 full days..
Regards