2. misc-audio
  3. 1167457199

Acoustical Foam

Curious whether others have experimented with acoustical foam. I ordered 1.75" foam tiles and foam corner kits. I have installed them tonight in the room that I'm preparing. There is no equipment in that room yet. I have 1/2 the foam tiles up on the walls. I will not be putting any on the ceiling as my wife has already commented that this is insane looking as is. I have been testing the acoustics by clapping my hands in the room before, during, and after the foam has been installed. So far, it has definately lowered resonances / echo, however, the room is not dead like a recording studio. Perhaps, once all the foam is up, an area rug is down over the wood floor, and there is equipment in the room, the room may be more dead sounding. That is certainly my hope. If it works, I will post more about exactly what I bought, the cost of the tweak, and my feedback on the cost/benefit of this change. Alot of the systems that incorporate acoustical treatments have big budgets for panels and other expensive room treatments, so my tweaks are certainly more budge oriented than aesthetically pleasing. I just purchased my first home, so my housing costs have nearly tripled. There definately is not as much money to play with these days, so I definately won't be purchasing expensive equipment as upgrades. That is why I'm trying to find tweaks that can have the sonic benefits of upgraded equipment at a much lower cost.
firecracker_77

Showing 4 responses by firecracker_77

firecracker_77 OP
26 posts
 
Herman,

I don't think the room will be dead sounding. I worked at 2 radio stations in my younger days, and the recording studios that were dead sounding had heavy steel doors and purpose built walls that could withstand artillery fire. This room is not that solid in construction, so it won't be completely dead and I'm not treating the ceiling so that will still provide some reflection. I bought the following:

http://cgi.ebay.com/24x24x1-5-Thick-Studio-Acoustic-Soundproofing-WedgeFoam_W0QQitemZ260065468799QQihZ016QQcategoryZ15199QQcmdZViewItem

Worst case scenario is that I don't like the foam, and I tear it down wasting about $300 that I spent.
firecracker_77 OP
26 posts
 
Interesting responses full of great information. I have put the foam on the walls immediately flanking and the wall behind my speakers and equipment. I have not treated the back wall where my chair will be located. From what I've read in this post, that is the opposite of what should be done, but at this point, I'm going to foam all the walls and then reverse tweak the room by removing foam until the desired goal is reached. For low frequency control, I have positioned 24"X10"X10" wedge shaped foam which joins at the junction of the ceiling and the walls. It is probably 6" thick at its greatest depth. I'm moving my equipment over tomorrow with the exception of my amp, speakers, and sub which are too bulky and heavy to move in our cars. I'm disassembling my MapleShade rack tonight. It weighs rougly 200 pounds assembled and is great to look at but is difficult to take apart and move when required. I will follow-up to this post once everything is going in that room. It is an experiment I'm looking forward to sharing here as the observations may be useful to someone else venturing down the path of room treatments which may not be as well understood as some more well known topics such as the differences between cd and vinly or the pros and cons of tube vs solid state amplification.
firecracker_77 OP
26 posts
 
Hey Chuttt,

I have approximately 2/3 of the walls covered now. I'm working from the front back to my chair. The room is getting a little less resonant now. However, I tested the higher mid frequency by whistling in the room the last time I was in there. It's not dull and muted sounding, but that's not obviously the range of frequencies as would be a cymbal crash. I will know the results of this experiment by Sunday, as I'm going to finish the room and set-up my gear. My parents and wife thought the room looked bizarre, but now that the walls are covered more evenly, I'm starting to like the way it looks. For a seamless look, I would recommend having the manufacture ship all pieces from the same production run to you. I rec'd mine in two shipments, and the pieces don't line up perfectly between the two orders even with the same product.
firecracker_77 OP
26 posts
 
My stereo has been powered up for a few days. I like the overall effect of the foam. I think that there is still sparkle in the treble. I'm not sure if I have lost much treble (probably have though based on the posts above), but I'm not unhappy with the results. I have posted pictures on my virtual system. For now, the foam stays. The room is 10 X 12, and I don't think it would sound very good without the treatment.
More to discover