2. cables
  3. 1231005386

PC Recommendation for Furman Conditioner

Hello. I have a Furman SPR-20i voltage regulator/conditioner and require a 20A IEC connector for my power cord.

I'm wondering if anyone can provide any recommendations on a PC to use. I have a VH Flavour 4 I'm currently using and could replace the 15A IEC with a 20A IEC as well instead of getting a new complete cord, (any recommendations on a good 20A IEC).

Also, I've been using a fair bit of stealth cables in my system and like how they present detail and neutrality in a laid back manner so I have been considering a Stealth PC, (never had one).

Also considering in no order....

Lessloss
Kaplan
DCCA
Tel-Wire (don't think they have a 20A IEC option though)

With the Lessloss I've heard some people don't think it's a good cable for a power conditioner, (although others say it is). I like the fact that it has high quality connectors though. With the Kaplan, it looks like the 20A IEC is only a 10 dollar part and while that may not make it bad, some feel the connectors are the most important part, (more so than the cable), but some feel it's close to a Kubala Sosna Emotion in terms of sound quality, (the only important measure).

Anyway, as you can see, lots of options and I know the "you'll never know, cables are so system dependent, etc" feeling. I'm just looking for opinions/thoughts. Thanks in advance.
bhoage
bhoage OP
112 posts
 
PS, I'd like to keep the cost below $1K, and the further the better but if there is a great PC close to that mark I won't rule it out. Thanks.
asmith
9 posts
 
I have been using a TG Audio SLVR PC on my 20A inlet power conditioner (Audio Prism Power Foundation III) for many years with great success. It's a great cord that improves imaging by providing a darker background without limiting dynamics as many PCs often do. The benefit of using it at the power conditioner is like upgrading all your components cords at once. Happy Hunting!
nick778
147 posts
 
Kimber makes the PK-10 Gold with the 20amp IEC option and retails for about $350. It isn't shielded for better sound so you need to keep it away from ICs and speaker cables but shouldn't be a factor in using it from the wall to the conditioner.

Of course you have your selection of Shunyata PCs but I haven't heard them. I have one of the Kimbers between the wall and my Hydra and like it for my main amp that draws a lot of power.
pmkap
18 posts
 
Bhoage,

You could give Mr. Cline at TelWire a call and see if he could provide an appropriate IEC to meet your needs.

As to why I offer the Hubbell brass contact h320c 20amp IEC on the KaplanCable as an option, its because it works very well with the copper plug I use. Heck, Synergistic uses Leviton plugs on cords that are amazingly good, and Kubala Sonsa uses Pass & Seymour. Why? I don't know, as they don't gel well with my wire and topology.
I've a satisfied customer using 2 20 Amp IEC cords for his BPT balancing conditioners, and another using his on the same Furman as yours. I much prefer, soundwise, my complement of connectors than my same cordage with the Oyaides I've evaluated.(but I've no experience with their 20amp versions) I can certainly provide any 20amp IEC you want, but would recommend you first evaluate our standard 20Amp cord.

Regards,
Paul Kaplan
KaplanCable
bhoage OP
112 posts
 
Thanks for your reply Paul. I hope it didn't come across like I was criticizing your cord, rather it was just an observation as I was thinking of re-terminating one of my own and was looking around at parts.

As I mentioned, your cord does seem to be discussed comparatively in some lofty circles, (both quality and price wise), so I can only assume that you're designing for sound first and foremost and price point is secondary, which you confirm above. It's even better that any savings seem to be being passed on to the customer in the form of a reasonable cost.

If you don't mind my asking, can you elaborate on what sound you're going for with your power cord?

Thank you very much for your time Paul.

Bryan
More to discover