"Musical" subwoofers? Advice please on comparing JL subs

Ah, but there is where you are wrong, the good ones do not have switching power supplies, that was precisely my entire point.   And the operational state of a solid state device is not a computer bit.  But that's OK, I really like the Class D and others should try them too.

Here's some of my thoughts on rooms and subs.

Right now, I'm figuring out the best location for my system in my room. It's about time. My room is 14.5' x 19.5' x 8' high. I listen across the 14.5" dimension out of necessity. I am using a readily available Room Analyzer package. This hardware/sofware generates audio sweeps, records the sound pressure with a mic, and calculates freq response, reverberation time, room modes, phasing and delay times. I am using a DIY sub. It has a 10" Scanspeak woofer in an acoustic suspension design. The main speakers are B&W 805s on the stands provided by B&W.

With the listening position against the wall opposite the speakers and the sub to the left of the left speaker, I've found several frequencies (40, 62, 125, 175 Hz and others) where there is a peak or null with a long delay time, much longer than other frequencies. Hand calculation of the expected room modes fits this observation. At 40 Hz, the sound wavelength is about 28'. Half wave is 14', which is nearly exactly the length I'm listening across. So room modes are important for an average sized room. The 40Hz peak is +10dB (above mean). the others have similar decay times but are not as strong, although the dip at 63Hz is nearly -10dB.
I moved my listening position (sofa) out  into the room away from the wall. I placed it 1/3 of the length of the room (recommended). New measurements are now quite different. All modes are suppressed to different degrees, but are still there. The software cannot find any modes, although I do have irregularities in freq response.
Listening position is a major factor in suppressing room modes. The explanation is that the new listening position is near a null in the 40Hz room mode. The conclusion is that room modes are important for bass. If you want good sounding bass from 30Hz upward, room modes must be considered.
Now, imagine I were to use the DARO system in my previous listening location. The DARO would call for 10dB suppression at 40Hz, but also for a approx +10dB increase in SPL at 63 Hz. This means that DARO would be calling for 100x more power from the sub amp (see https://geoffthegreygeek.com/amplifier-power/). This is very difficult to do for most amps. The DARO can reduce peaks, but cannot be used effectively to remove dips.

In order to effectively suppress modes, several things are needed prior to using DSP.
.First, get the sub away from the walls and corners. Get it (them) out into the room (unless you want your bass to overpower everything else).

Second, use the recommended listening position.
Third, after the first two are done and characterized, add room treatments that includes corner traps and bass traps for the low frequencies. These absorb the appropriate frequency bands so the standing waves are absorbed, not reflected. Additionally, the long reverberation will be dramatically reduced.
The first two modifications will get you a long way, but room treatment is absolutely needed to suppress the remaining modes, unless you are fortunate or the modes are sufficiently suppressed for your taste.

After the above three things are done, then the DSP (such as DARO) can be used as the peaks and nulls will be of lower amplitude and therefore the amp will not be stressed as severely.
In conclusion, room modes determine the lower frequency response of an audio system. The exact modes depend on the room size and geometry. Room modes cannot be corrected entirely with DSP software, especially nulls (dips). 
The modes are there whether DSP is used or not. Optimal location of the sub(s) and the listening position is vitally important. To avoid excessive use of amplifier power, add room treatments prior to adding DSP.
Please note that there are other considerations if two or more subs are used as they can be placed such that certain room modes can be suppressed. But room modes are still present since these are characteristics of the room only . One person's solution may not work for someone else. Other modes may not be.suppressed. Room modes are always present in a room since these are characteristics of the room only . It doesn't matter what is in the room, the modes still exist. Any item added to the room can only affect the relative amplitudes of the room modes (this goes for treatments also). One person's solution may not work well for someone else.

Even without a room analyzer, one can improve the performance of an audio system. Searches will provide guidelines, such as placing the listening position about 1/3 (actually 0.38) of the distance between the walls behind the speakers and the listener..

Some boilerplate - I am not affiliated with any manufacturer of audio equipment, room treatments or DSP. I have no interest in selling you anything.  I have an MS in Physics and over two decades designing and building optical systems (telescopes for example). Wave phenomena are very familiar to me.
Constructive criticism is always welcomed.

My apologies to everyone. I meant this screed for another topic on this forum. Perhaps it will add to the discussion. If not, feel free to erase it. I'm very new.