Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57

Hi all, owners that like to try different ways of powering their Lightspeed Attenuator’s. May like to try something new that Stereophile gave some push for.

It’s the new iFi iPower supply dc wall wart, now before any of you say it, yes I didn’t like recommending smp (switch mode) wall warts. This was only because the ones I tested had a bit of noise, that couldn’t be heard, yet was measurable when compared to a linear wall wart.

This new iFi iPower supply wall wart is smp, yet it’s noise is very low.

http://www.stereophile.com/content/music-round-77#61wYlEfbAywkfiS2.97

http://ifi-audio.com/portfolio-view/accessory-ipower/

If you order one be sure to get the 12vdc one with 2.1mm X 5.5mm plug with centre positive.

Lets please hear a review from anyone that gets one, as I may change to these as supplied wall wart with the Lightspeed Attenuator, as they are multi world wide voltage usable.


Cheers George



This is what Kalman Rubinson of Stereophile heard when he used this new iFi iPower wall wart on a low powered dac when he compared it to a linear wall wart, it should/could do the same for the Lightspeed Attenuators sound.


"When I switched over from the stock supply, the DAC didn't seem quieter when there was no audio signal, but that's not the real test. Recordings with open, ambient soundstages sounded cleaner, and both instrumental and vocal music was more distinct. This was no major change that struck me every time I listened, but it did make all of my listening much more relaxing—perhaps because, subliminally, it required less effort to attend to individual sounds, particularly those far back on the soundstage."


It has some pretty impressive measured noise figures, of 1uV of noise, (that's microvolt not millivolt)!!!!!

This could be a deal breaker, and the end of linear wall warts for the Lightspeed Attenuator.

I tried to find advertised pricing of them, but couldn't get an exact figure, but it seems to be around $50-$100 which should be a great upgrade for that kind of low noise supply.


Cheers George  

The Stereophile 'push' is working: it's out of stock everywhere I've looked. fyi: it's US$50

Thanks banquo, $50 is a very good price if it does what's claimed, can you supply a link to where you got this price, I like to get one when they've replenished their stock.


Cheers George