single versus multiple driver?


I have for years been thinking over the idea of a single driver easy load speaker with low powered set amps. I would love to take the plunge but am a little weary about the performance and risk. I listen to mostly classical,opera,jazz,older pop recordings and the like. I am presently using a pair of sounddynamics three way 300ti speaker and driving them B&K M200 amps. also bass is supported with the use of a Rel StrataIII sub. I am asking the question have any gone to single and been very disapointed and gone back to multiple drivers? I mean it really seems like a no brainer single speaker with no crossover should account to better sound? Thank you all and happy holiday.
schipo
Been there and back and then back again only to leave(kinda).

I've had very modest single driver experience so take this with a major grain of salt. Had Ed Schilling;s little horn, and now Omega's Super 3 xrs. In between I've had Magnapan;'s LS3 5a's, Devore's etc....

Single drivers can be extremely musical, even revelatory if your tastes in music cooincide with their strengths. Utimatley I think that you can get "there" a bit easier with multiway's than with singles but others will disagree.

I've heard lowthers, phy's, and many fostexs in various configurations and some were very very serious attempts at full range sound. They all were mighty impressive but....

Right now I'm intrigued with my current setup. 4.5 inch hempcone(Omega xrs) with a foutek ribbon tweeter on top with just a single cap as a crossover, very nice and the process of picking the right cap teaches you a lot about speaker voicing.

Every serious audio nut should try it. If I had the luxury of multiple listening rooms there is no doubt one would be a single driver setup. Not having a crossover in the critical midband is something that is hard to give up once experienced.
i have several setups, fortinate i know. i have a 4.5" fostex with an 8" sub, it has a presence and detail that my more conventional 3 way and 2way setups do not. i have never heard the larger single drivers, nor the big transmission line and horn enclosures. . however, the more complicated the sound the more difficult it is for the smaller single drivers to do. if you like music that is acoustical and vocal, the singles excel.

if you have the luxury, try the little guys with your sub, see how you like them, i think you will be grateful you did
Multi-driver configurations can cover the frequency spectrum better, but have problems with phase coherence, time-delay, spatial irregularities. Various technical solutions mitigate these, but cannot eliminate them.

Single-drivers have their own advantages and problems: excellent coherence and presence, but limitations in frequency response and their own coherence problems when it comes to complex music.

Coaxial drivers offer a "middle way" that overcomes some of the limitations of both approaches. They must still use a crossover, but it can be simple, and it overcomes the the multi-driver's artificiality of having musical information coming from two or more points in space.

For my ears and budget, coaxials offer the best compromise (remember that all speakers are a compromise) between the virtues of the single-driver and the multi-driver approach.

They are by definition more expensive to engineer and manufacture than two comparable separate drivers.

Try the Great Plains Audio 604-8H-II (www.greatplainsaudio.com) or the Iconic 704-8A (www.iconicspkrs.com) or any of the 12" or 15" Tannoy dual concentrics (I prefer those from the "DMT" series, made from about 1990 to 2002; others swear by the vintage Tannoy models: Monitor Golds, HPDs, etc.)

Another advantage of the coaxials is that is relatively easy to buy raw drivers and crossovers and make, or have made, your own cabinets, which saves serious money compared to buying factory-made cabinets.

Serious Stereo (www.seriousstereo.com) makes a very fine speaker based on the GPA 604-8H-II, but a pair is circa $10K, whereas you can buy the raw drivers direct from the manufacturer for under $1500/pr. and make your own cabinets.

Another advantage of these drivers is a feature they share with many single-driver designs--high sensitivity (95-100 dB), which leaves you free to use low-power SET amps or high powered solid state or anything in between.

BTW, I have no affiliation with any of the companies I mentioned; I'm just a long-time and satisfied user of some of their products.

Happy listening!

Joel.
A driver large enough to produce low frequencies has too much mass to allow for the quick movement needed to produce higher frequencies. That's why a single driver is not used, except in things like portable radios. Devices that use a single driver will be compromised too much in either high or low frequencies relative to a good multi-driver design. Otherwise, everybody would be making them.
cone drivers are usually not as linear as electrostatic drivers, ribbons or planar magnetic drivers.

so the question should include these drivers as well.
i believe cones are flawed, whether one or several.
cabinets and crossovers do not help either.

it surprises me that there are so few panel designs commercially available.